The main wear mechanism is adhesive wear and abrasive wear.
该材料的主要磨损机制为粘着磨损和磨粒磨损。
Oxidation and adhesive wear of the coating is lighter than that of the steel.
钢的氧化磨损和粘着比涂层严重。
Bat a decisive factors of ring failure are the adhesive wear and fatigue wear.
而钢领失效的决定性因素是粘着磨损和疲劳磨损。
The main wear mechanisms are oxidation wear, adhesive wear, and abrasive wear.
主要磨损机制为氧化磨损、粘着磨损和磨粒磨损。
The wear mechanisms during dry sliding process are oxidation wear and adhesive wear.
在干滑动摩擦过程中，磨损机制主要为氧化磨损和粘着磨损。
Adhesive wear and surface - fatigue wear are the two major wear forms in rail steel.
粘附磨损和疲劳磨损是轨钢的主要磨损形式。
The wear mechanism of the nanotube layers involved abrasive wear, fatigue wear, adhesive wear and oxidative wear.
纳米管层的磨损机理主要为磨粒磨损、疲劳磨损、粘着磨损和氧化腐蚀磨损。
There are five forms of wear and wear: abrasive wear, erosive wear, adhesive wear, fatigue wear and corrosive wear.
磨损有五种磨损形式：磨料磨损、冲蚀磨损、粘着磨损、疲劳磨损和腐蚀磨损。
The textured surfaces exist oxidation wear, abrasive wear and adhesive wear in the condition of line contact rolling.
在线接触滚动过程中，存在氧化磨损、磨粒磨损和黏着磨损。
The results shown that the slurry erosion wear of adhesive coating is composed of adhesive wear and antiwear filler wear.
结果表明，这种涂层的冲蚀磨损是由粘结剂的磨损和抗磨填料的磨损所组成；
The main wear mode of PPS is changed from adhesive wear into abrasion wear with the addition of PTFE and kaolin nanoparticles.
PTFE和纳米高岭土的加入使PPS的主要磨损方式由粘着磨损转变为磨粒磨损。
An adhesive wear model based on fractal parameter is derived on the grounds of adhesive wear theory by modifying the M-B fractal contact model.
在对M - B接触分形模型改进的基础上，根据阿查得粘着磨损理论导出了基于分形参数的粘着磨损模型。
The abrasive wear, fatigue wear and adhesive wear are the main factors causing the excess wear and breaking of the driving chain on drilling RIGS.
磨料磨损、疲劳磨损和胶合等是引起石油钻机传动链条磨损超限，承载；能力降低，最后导致链条断裂破坏的主要原因。
The main wear mechanism of MoSi 2 material is fatigue wear under the lower loads, while adhesive wear is the main mechanism under the higher loads.
低载荷下的磨损机制以疲劳磨损为主 ，高载荷下的磨损机制主要表现为粘着磨损。
The failure mechanism of journal bearing of roller cone bit is analyzed, the failure type is adhesive wear, and main factors affecting the adhesive wear are analyzed.
分析了牙轮钻头滑动轴承失效的机理，论证了牙轮钻头滑动轴承失效形式主要为粘着磨损，分析了影响轴承粘着磨损失效的主要因素。
In calf serum medium, the wear mechanism of fretting is mainly adhesive wear, fatigue wear and the weakening effect of solution molecules on the bone cement matrix under stress.
骨水泥在小牛血清介质中微动磨损的损伤机制主要为黏着磨损和疲劳磨损，溶液分子在应力作用下对骨水泥基体有削弱作用。
The wear rate initially increases and then decreases with sliding distance increasing in all tested materials, wear mechanism during dry sliding process is oxidation wear and adhesive wear.
干滑动摩擦磨损率随磨损滑移距离的增加先增加而后逐渐降低，磨损机制主要为粘着磨损和氧化磨损。
It is finally pointed out that the main wear mechanisms of the ceramic tool materials are still abrasive, adhesive, chemical reaction and dispersion wear.
指出陶瓷刀具材料切削磨损时的基本机理仍然是磨料磨损、粘结磨损、化学反应与扩散磨损。
The wear properties of antiwear adhesive coatings under solid particle erosion and slurry erosion condition were studied in this paper.
本文对气固冲蚀和浆体冲蚀条件下耐磨环氧胶粘涂层的磨损特性进行了研究。
Aimed at the abrasion of pins, some experiments were carried out and the abrasion course was analyzed, the abrasion course of pins is the breaking-in, the abrasion wear and adhesive abrasion.
通过大量试验，分析了装载机销轴磨损的历程，表明销轴的磨损历程主要分为磨合阶段、磨粒磨损阶段和粘结磨损阶段。
The process of wear was from adhesive to abrasive, the gold plating was worn out at last.
磨损过程为先粘结再擦伤，最后镀金层被磨穿。
The abrasion properties of wear-resistant adhesive coatings have been studied on self-created abrasion test facility.
利用自制冲蚀磨损试验装置，研究了耐磨胶粘涂层气固冲蚀磨损的特性。
The content of PTFE powder filled in the epoxy adhesive can affect the impact strength, adhesive strength, hardness and dry-wear property of the adhesive.
介绍用聚四氟乙烯粉填充于环氧胶中，研究了粉的含量对冲击强度、粘接强度、硬度、干磨性能的影响。
The adhesive condition of wheel and its effects on the wheel wear are analyzed, and the restraint measures of wheel adhesion is proposed.
分析了磨削中的砂轮粘附情况及其对砂轮磨损的影响，提出了抑制砂轮粘附的措施。
The adhesive strength of the films to the substrates, diamond-coated tool wear and surface roughness of the workpiece were further studied by turning glass fiber reinforced plastic cylindrical bars.
通过玻璃纤维增强塑料的车削试验，研究了薄膜与基体之间的附着强度、涂层刀具的磨损和加工工件的表面粗糙度。
Wear resistance—The chip-tool and chip-work interfaces are exposed to such severe conditions that adhesive and abrasion wear is very common.
耐磨性—切屑-刀具与切屑-工件的接触界面处于如此严酷的状态，粘附和磨损是很普遍的。
Based on this study, a adhesive transfer mechanism is proposed for the formation of transferred films during sliding wear in this paper.
在这一研究的基础上，本文对滑动摩擦转移膜的形成提出粘着转移机制。
The obtained stainless steel colored film is bright and beautiful, assuming the golden color, which has excellent corrosion resistance, wear resistance and good adhesive power.
所得到的不锈钢着色膜光亮美观，呈金黄色，具有优良的耐蚀性、耐磨性和良好的附着力。
The obtained stainless steel colored film is bright and beautiful, assuming the golden color, which has excellent corrosion resistance, wear resistance and good adhesive power.
所得到的不锈钢着色膜光亮美观，呈金黄色，具有优良的耐蚀性、耐磨性和良好的附着力。
应用推荐