The preheat oven is used to bring the pump up to the metal bath temperature.
进口工业网的预热烤箱是用来使泵送金属浴温度。
Coagulant bath temperature had a strong influence on PU, PES composite flat membrane.
凝固浴温度对填充聚合物平板膜有很大影响。
The ultrafiltration rate of pure water with the coagulation bath temperature increased.
随着凝固浴温度的升高，所成的膜的透水速率上升。
Try to put vanities, bath temperature water, such as water turbidity found to water until the clear-up.
要试放面盆、浴缸的冷热水，如发现水质混浊，须放水，直到水清为止。
These crosslinkers are stable in water at normal bath temperature but become reactive at curing temperatures.
这些交联剂于正常槽液温度下在水中很稳定，但在固化温度下就变得活泼起来。
Special procedures are used to ensure that these crosslinkers will not react at bath temperature to cause instability.
通过采用一些特殊的处理工艺，确保这些交联剂不会在槽液温度起反应而引起槽液的不稳定性。
Moreover, the pore density has a strong dependence on PEG content, water bath temperature, water bath time and solvent.
孔的数量与PEG加入量、水浴温度、水浴时间及溶剂等密切相关；
Porosity increases along with the increasing of coagulation bath temperature, and doesn't have relation to pre-evaporation.
孔隙率随着凝固浴温度的上升而上升，而与预蒸发时间的长短没有关系；
Low liquidus temperature enables low bath temperature. The current efficiency increases with the decreasing of bath temperature.
低液相线温度允许低电解温度，而降低电解温度可大大提高电流效率。
The effects of precursor concentration, PEG2000 content and water bath temperature on the characteristics of films were studied.
研究了前驱体浓度、PEG2000加入量及不同水浴温度对薄膜结构和性能的影响。
Thermal equilibrium can be used for predicting bath temperature at endpoint only with stable raw materials supply and operation.
只有减小原料条件的波动和稳定操作，才可用热平衡方法预测吹炼终点熔池温度。
This technology holds great practical values in raising the bath temperature for hard anodic oxidation of aluminium, improving t…
该工艺在提高铝硬质阳极氧化槽液温度、增加膜的硬度和节能等方面都县有很大的实用价值。
The effect of additive varieties, bath temperature, current density and plating time on the satin nickel coating are also discussed.
同时还研究添加剂的种类、镀液温度、电流密度、电镀时间对镀层性能的影响。
The studies on stability of PU-SiO2, PES-SiO2 suspensions and influence coagulant bath temperature on flat membrane were carried out.
研究了无机粒子填充聚合物悬浮铸膜液的稳定性及凝固浴温度对平板膜成形的影响。
The results showed that the properties of the regenerated bamboo fiber prepared with lower coagulation bath temperature were improved.
实验结果表明：在较低的凝固浴温度下纺制得到的再生竹纤维素纤维的性能较好。
To comprehend the change law of bath temperature in blowing of large converter the sublance is used for measuring the temperature and sampling analysis.
为了了解大型转炉吹炼过程中熔池温度的变化规律，利用副枪在转炉吹炼过程中进行了测温和取样分析。
In order to keep the normal bath temperature and slag forming condition, the charge of pig iron should not be exceeded 10 % on middle and small converter.
中小型转炉内生铁块的加入量不应超过10 %，使转炉吹炼过程中保持正常的熔池升温和成渣状况。
Microcomputer control, touch switches, seven files of arbitrary power conditioning, meet the needs of different bath temperature, faster and more comfortable.
微电脑控制，触摸开关，七档功率任意调节，满足不同洗浴水温，更快捷，更舒适。
Besides the cell voltage, bath temperature and bath ratio, the inputs of the system also include the liquidus temperature, superheat extent and cathode voltage.
系统的输入参数除传统的电压、温度和分子比外，还采用初晶温度、过热度和阴极压降等作为系统的输入参数。
The effects of spinning dope concentration, coagulation bath temperature and addition of persimmon leaves on the mechanical properties of blend fiber were studied.
研究了纺丝原液浓度、凝固浴温度、柿叶添加量对共混纤维的力学性能的影响。
The retention rates of Albumin bovine decreases when coagulation bath temperature increases, and first decreases, then increases when pre-evaporation time prolongs.
对牛血清白蛋白的截留率随着凝固浴温度的上升而下降，随着预蒸发时间的延长先略有下降然后上升。
This technology holds great practical values in raising the bath temperature for hard anodic oxidation of aluminium, improving the film hardness and energy saving etc.
该工艺在提高铝硬质阳极氧化槽液温度、增加膜的硬度和节能等方面都县有很大的实用价值。
The influence of ammonium molybdate, cobalt sulphate, ammonium bifluoride, acidity of blackening bath, blackening bath temperature and time on film quality were studied.
研究了钼酸铵、硫酸钴、氟化氢铵、黑化液酸度、黑化液温度及时间对膜质量的影响。
It was noted that when coagulation bath temperature was increased, crystallization could be suppressed, and more porous structure was obtained on the surface of the membrane.
另外，凝胶浴温度升高可以抑制结晶现象，并使膜表面孔径和孔密度增加。
Based on this platform, a fuzzy expert system of aluminium fluoride's feeding is developed. It is applied to controlling of the aluminum electrolysis's bath temperature and ratio.
以此专家系统为平台，开发了电解铝过程中氟化铝添加的模糊专家系统，控制电解质温度和分子比。
The accuracy of the prediction is determined by the reliability of initial carbon content. The bath temperature is a function of the carbon content and the CO, CO2 partial pressure.
熔池温度是碳含量及炉气中CO和CO2分压的函数，其中吹炼过程的平稳性是模型最终预测结果准确获得的保证。
The bath temperature, liquidus and anode effect were controlled by adjusting the AlF3 additions, aluminum tapping magnitude, cell voltage set-point and the alumina feeding interval.
通过调整氟化铝添加量、出铝量和设定电压，以及氧化铝下料间隔的自修正，实现对电解槽温度、初晶温度、效应系数的控制。
His body temperature was so high that when he arrived unconscious at Kalgoorlie hospital, medical staff could not cool his body down, despite giving him an ice bath.
他的体温很高，以至于送达卡尔吉利医院的时候已经处于昏迷状态。医务人员用冰块给他擦拭身体，也无法使他的体温降下来。
Also note that the temperature of the bath increases significantly during this process.
同时要值得注意的是，在电解过程中槽内的温度会显著上升。
Also note that the temperature of the bath increases significantly during this process.
同时要值得注意的是，在电解过程中槽内的温度会显著上升。
应用推荐