使用安装在冻干机内的液压装置或螺杆全加塞。
Complete stoppering of the vials usually by hydraulic or screw rod stoppering mechanisms installed in the lyophilizers.
自主开发出了在冻干机上实施动压法的软件系统。
Independently develop software system of dynamic pressure rise measurement actualized on freeze-dryer.
以新型冻干机为基础，对香菇真空冷冻干燥工艺进行研究。
It research the vacuum freeze-drying process on the base of new freeze dryer.
本文介绍了冻干机的热回收系统并进行了热回收的能量分析。
The paper describes the heat recovery system of freeze-dryer and its energy analysis.
在冻干机清洗验证中的好的方法是在清洗的前后进行表面取样。
It is a good practice as part of the validation of cleaning of the lyophilization chamber to sample the surfaces both before and after cleaning.
为了最小化油蒸汽的回流，一些冻干机在真空泵和前箱间设计了弯曲的管路。
In order to minimize oil vapor migration, some lyophilizers are designed with a tortuous path between the vacuum pump and chamber.
本文主要介绍在冻干机测试技术控制中采用DSP芯片控制冻干工艺的实验方法。
The main purpose of this paper introduce the experiment method of freeze drying measurement technology in DSP control.
目前生产销售的药用真空冷冻干燥机，食品冻干机二大系列十四种规格的干燥设备。
At present, this company manufactures and sells two series of drying equipment, namely the medical vacuum freeze dryer and foodstuff freeze dryer of fourteen specifications.
方法在透析后的几丁糖与明胶混合液中加入戊二醛交联后置入冻干机冻干制得几丁糖膜。
Method chitosan film was prepared by casting the mixed solution of dialysed chitosan and gelatin after crosslinking with glutaraldehyde in freeze dryer.
对影响冻干机冷阱传热性能的两个因素(冷阱盘管壁面温度和结霜厚度)进行了实验研究。
An experimental study on the performance of freeze-dryer's cold trap has been carried out under different temperature of the cold trap coil and different frost thickness in the paper.
介绍了冷冻真空干燥设备的种类、规格、用途和选型方法，供使用冻干机的用户采购设备时参考。
This paper presents the types, models, technological specifications, and the scope of application of freeze vacuum drying equipment, especially how to select proper dryer by using these introductions.
还有的生产商建造新的车间时，将灌装线和冻干机摆放的很近，并且在灌装机和冻干机之间安装主要的屏障。
Other manufacturers building new facilities have located the filling line close to the lyophilizer and have provided a primary barrier extending from the filling line to the lyophilizer.
结果冻干机性能好坏、冻结过程的改变和制品入箱时冻干机板层温度的变化是决定制品产生粗结晶的主要因素。
Results The property of freeze dryer, the variation of lyophilized process and the change of temperature of plates may induce rough crystal of products.
计算结果可以用于估算冻干机内不同部位物料的干燥速率，并可为确定冻干机关键结构工艺参数提供重要的理论参考依据。
The analysis conclusion can be used to estimate the difference of material drying rate at different parts in equipment and to direct the choice of structural and process parameters.
计算结果可以用于估算冻干机内不同部位物料的干燥速率，并可为确定冻干机关键结构工艺参数提供重要的理论参考依据。
The analysis conclusion can be used to estimate the difference of material drying rate at different parts in equipment and to direct the choice of structural and process parameters.
应用推荐