烧结温度的升高提高了烧结收缩率。
The sintering shrinkage increased with increasing sintering temperature.
模具收缩率，流动，3.2毫米。
他们对预聚体收缩率的变化要求比较高。
They are relatively demanding upon the shrinkage change of performed polymer.
钢和混凝土有几乎相同的收缩率和膨胀率。
Steel and concrete have almost the same rate of contraction and expansion.
塑件的尺寸公差不能低于收缩率的10%。
The dimensional tolerance of plastic parts shall not be less than 10% of shrinkage.
探讨了影响涤纶短纤维收缩率的工艺条件。
The technology conditions that have effect on polyester shrinkage rate were discussed.
低收缩率，低光学吸收率，低折光指数粘合剂组合物。
Low shrinkage, low optical absorbance, low refractive index adhesive composition.
测量此方法的皮片收缩率，并与其他种类皮片进行比较。
The contraction of the skin grafts were measured and compared with other kind of skin grafts.
精确度：尺寸稳定性极佳，模塑收缩率低，热膨胀率低。
Accuracy: dimensional stability, low mold shrinkage, low thermal expansion rate.
在压力降低的情况下收缩率高于正常原油收缩率的原油。
Crude oil that has a greater shrinkage with pressure reduction than normal crude oil.
二次热收缩率小，平整度好；用于柔性印刷线路板等行业。
Low secondary thermal shrinking rate, good flatness; Used for Flexible Printed Circuit (FPCB).
但是，他们在不同的收缩率，从而使黑色铜氧化物片赶走。
But they shrink at different rates, which makes the black cupric oxide flake off.
成型收缩率小，尺寸稳定性好，熔体粘度小，易成型加工。
Molding shrinkage of small, good stability, melt viscosity size is small, easy forming process.
从实验分析入手，介绍一种实时测量光敏树脂收缩率的测试方法。
This paper introduces a method for real time measurements of the shrinkage of the photopolymer.
探讨了聚丙烯改性生产中各种改性剂对聚丙烯改性料收缩率的影响。
The influence of various modifiers on the shrinkage of modified PP in the modified PP production is inquired.
该材料具有较好的物理机械性能，热收缩率达96 ~ 100%。
The materials have good physical and mechanical properties and 96-100% shrink ratio.
固相质量分数和引发剂质量分数都会影响坯体的线性收缩率和密度。
Both solid volume fraction and dispersant volume fraction had some effects on shrinkage and density of green body.
结果表明，MTC固化体的体积收缩率远小于水泥石的体积收缩率。
The results show that the volume shrinkage of MTC solidified body is far less than that of conventional cement.
通过掺加添加剂，有效地改善了轻质墙体材料通常存在的收缩率大的缺点。
It has been improved the disadvantage of large shrinkage-rate in light-weight wall materials by adding additive.
复合硅酸盐保温材料可塑性强、导热系数低、耐高温、浆料干燥收缩率小等特点。
Composite silicate insulation material plasticity, low thermal conductivity, high temperature resistant, low pulp drying shrinkage rate, etc.
当杆的断面收缩率比杯形部分断面收缩率大得较多时，不适合直接用复合挤压成形。
When the shrinkage of the rod fracture surface much more than that of the cup part fracture surface, its formation by compound extrusion is not applicable.
研究了热懈温度和保温时间对陶瓷产率、线收缩率、力学性能以及微观结构的影响。
The effects of pyrolysis temperature and soaking time on ceramic yield, linear shrinkage, mechanical properties and microstucture were investigated.
实验结果表明：改性环氧丙烯酸酯可以明显改善体系收缩率，稀释剂对收缩率有影响。
The results showed that the shrinkage of system were improved obviously by adding modified epoxy acrylic ester, and the diluent had effect on shrinkage.
研究了一种满足新型汽车车灯反射器的使用要求的低收缩率的耐高温不饱和聚酯模塑料。
This paper introduces a high-temperature resistant and low shrinkage unsaturated polyester molding compound used for a novel reflector of automobile lamp.
分析了腈纶干法丝束制条中影响产品质量的毛条长度、蒸汽收缩率、条干不匀率等因素。
The influential factors on the quality of dry-spun PAN bully tops, such as length, steam shrinkage, yarn irregularity, were analyzed.
通过测试研究还得到两种钢筋的极限强度、延伸率和断面收缩率等其他高温力学性能参数。
According to the testing and studying, ultimate strength, elongation and shrinkage on cross section of two kinds of steel bar were determined.
特别是树脂的固化体积收缩率显著降低，从7％下降到0.8％，明显改善了涂膜的平整性。
The volume shrinkage of the sample was lowed from 7% to 0.8%, which apparently smoothen the film.
特别是树脂的固化体积收缩率显著降低，从7％下降到0.8％，明显改善了涂膜的平整性。
The volume shrinkage of the sample was lowed from 7% to 0.8%, which apparently smoothen the film.
应用推荐