即唐氏螺纹紧固及硬锁紧螺母紧固。
通过各种测试，强力锁紧螺母已被证明是有效的。
Hard Lock Nuts have been proven effective in a variety of tests.
它由称套、锁紧螺母、锁紧垫圈组成。
调整后，就将锁紧螺母拧紧。
调整后，拧紧锁紧螺母。
强力锁紧螺母非常适合在飞机，汽车和建筑的应用当中。
Hard Lock Nuts are ideal for use in aircraft, automotive and construction applications.
用于夹持侧铣刀，铣刀由垫片和锁紧螺母固定。
For clamping side milling cutter. The arbor are supplied with space ring and clamping nut.
用扳手抓住上部和下部阀杆锁紧螺母并且松开。
逆时针方向旋转锁紧螺母5，使其退到适当位置。
Revolving the lock nut 5 anti-clockwise to the suitable position.
双件套强力锁紧螺母安装简便，只需要一个扳手就行。
The two-piece Hard Lock Nut is easy to install, requiring only the use of a wrench.
卸下 通风窗4后，松掉锁紧螺母5上的锁紧螺钉。
如果您想调节它的位置，需要订购另外一个锁紧螺母。
You'll need to order an extra jam nut if you want position-adjustability.
松开回转叉架的锁紧螺母，将料斗推出转到下一工序。
Loosens rotates boom's stopping nut, promotes the hopper changes to the next working procedure.
在调节完成后，紧固锁紧螺母，重新安装快速进水手柄帽。
After completing adjustments, tighten the lock nut and replace the fast fill lever cap.
松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。
Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem.
六角锁紧螺母是一种有非金属物质(通常为尼龙)的颈圈嵌入的螺母。
They are the nuts with nonmetallic elements (normally Nylon insert) full collars or rings at the top.
如果要清洗或更换部件，关闭供应管道，松开锁紧螺母，退出调节螺丝。
To clean or replace parts; shut off supply, loosen lock-nut and back off adjusting screw.
锁紧二连杆的调整机构和瞄准镜中部的二个光楔锁紧螺母（图1序号7）。
Lock adjusting mechanism of two connecting rods and two optical wedge lock nuts of sighting telescope center (No. 7 in Fig. 1).
滤筒的安装1。将滤筒推入每个支架中，按顺时针方向旋上并锁紧锁紧螺母。
Third, the cartridge installation 1 will push the cartridge into each bracket in a clockwise direction and tighten the lock nut on the screw. 2.
气动制动器，气动离合器，直线导轨，锁紧螺母，关节轴承为我公司代理产品。
Pneumatic brakes, pneumatic clutch, linear guide, locking nut, joint bearings for my company Products.
锁紧螺母扭矩压紧垫片时，其与垫片的最大相互作用力不能超过表3所给扭矩值。
The locknut torque needed to move the washer at the maximum washer interference fit shall not exceed the torques given in Table 3.
构件失效的主要原因是：锁紧螺母的热处理工艺不当，止动垫电镀过程发生氢脆。
The results show that the failure is mainly attributed to the inappropriate heat-treatment technology of the locking nut and the hydrogen brittlement from electroplating of the stopping pad.
小尺寸轴承使用带锁紧垫圈的锁紧螺母大尺寸的轴承使用带锁紧卡箍的锁紧螺母。
Smaller sizes use a lock nut with a locking washer, larger sizes use a nut with locking clip.
将混合料斗推入回转叉架并锁紧螺母，启动控制系统，能自动将料斗提升至混合高度并不可靠定位。
Will mix the hopper to thrust rotates the boom and the stopping nut, the start control system, can automatically the hopper promotion to the mix highly absolute fix.
针对高速线材生产中，精轧机辊轴及隔套锁紧螺母存在的问题进行分析，提出了改进措施，取得了较好效果。
The problems in lock nut of roll axis and sleeve of precision rolling mill are analyzed, some measures proposed, good result got.
本实用新型一种环箍是由箍带、锁紧螺母等构成，其特点是所述的锁紧螺母的钢丝螺套有一至多圈呈多边形结构。
After the wire thread insert of the hoop of the utility model is installed in the nut, the elastic deformation generated from the radial of the wire thread insert is used to lock the screw.
CY 6102型柴油机减振器锁紧螺母发生多次失效、漏机油等故障，造成柴油机无法正常工作，甚至导致柴油机损坏。
Many cases that damper locking nuts of CY6102 series diesel engines loosened and lubricating oil leaked from the dampers, which caused the engine fail to operate and even damaged happened many times.
甚至在螺母松脱45度的情况下，其一半以上的锁紧扭矩仍然不变。
Even when loosened by 45 degrees, more than half of the tightening torque remained.
当上螺母的凹面与之锁紧时，其效果与用一个锤子敲进一楔子的效果完全相同。
When the concave upper nut is tightened, the effect produced is exactly the same as that produced by a hammer driving in a wedge.
当上螺母的凹面与之锁紧时，其效果与用一个锤子敲进一楔子的效果完全相同。
When the concave upper nut is tightened, the effect produced is exactly the same as that produced by a hammer driving in a wedge.
应用推荐