Finally, a substation automation system is designed, which is based on the MMS protocol.
最后，设计了一套基于MMS协议的变电站自动化系统方案。
This paper presents a substation automation system based on Fieldbus where PLC is used as the control unit.
本文提出了一个构建在现场总线网络之上，采用PLC作为控制单元的变电站自动化系统的实现方案。
In this system the technology of automatic master station is used for the substation and on this basis a substation automation system is constructed.
该系统将自动化主站系统的技术引入变电站，构建了变电站自动化系统。
ABB will also install a substation automation system compliant with the global IEC 61850 communications standard, and equipped with the latest protection and control products.
ABB还将安装一个兼容全球IEC 61850通信标准的变电站自动化系统，并配备最新的保护和控制产品。
Not only will it be connected with substation and dispatching automation system but also can lay a foundation of distribution feeder automation system.
既能与目前广泛应用的变电站综合自动化、调度自动化系统相结合，又可为配电自动化打下基础。
Communication network is a key technique in substation automation system.
通信网络是变电站自动化系统的关键。
A scheme for adding the function of multimedia information acquisition and transmission to the existing substation automation system by adopting the multimedia RTU is also proposed.
提出了采用多媒体rtu，以实现现有变电站自动化系统增加多媒体信息采集与传输功能。
Non-electrical quantity detecting system is a new auto-control system that adapt automation of electric scheduling, self-service and integrating automatism in substation.
主变非电量测控系统是适应电力调度自动化、变电站实现无人值班化和综合自动化的一种新型自动测控系统。
Based on this, by combining the operation sequence of control in substation automation, a security communication system of remote control for substation automation is designed.
在此基础上，针对变电站远程控制的安全需求，结合变电站自动化控制操作的动作序列，设计了变电站自动化远程控制的安全通信体系。
Research the application of 100m Ethernet in substation automation system, and provide a new network configuration of substation automation system base on 100m Ethernet.
研究快速以太网在变电站自动化系统中的应用，提出了基于100M以太网的变电站通信网的网络结构。
To analyse substation automation product, testing technology and methods, this paper presents a design method of test system for substation automation product.
对变电站自动化产品和测试技术、方法进行分析，提出了一种变电站自动化产品测试系统的设计方法。
Circuit breaker tripping coil burning is a relatively frequent accident for the operation of substation comprehensive automation system.
断路器跳合闸线圈烧毁事故是变电站综合自动化系统在运行中较普遍的现象。
The introduction of IEC 61850 is a good chance for our country to develop new substation automation system to catch up with the advanced technology in the world.
IEC 61850标准的引入，为我国研制下一代变电站综合自动化系统，追赶国际先进水平带来了新的契机。
Have set up a experiment model of substation automation system non-real-time network communication by using HTTP XML and VC.
利用HTTP、XML以及VC建立了变电站自动化系统非实时网络通信实验模型。
This paper introduces a new integrated automation system which is suitable for any kinds of substation.
本文着重介绍了适用于各类变电站的综合自动化系统。
It is feasible to enhance the substation automation system for digital substations through designing a lot of advanced applications by using SCD file.
通过运用变电站配置描述文件可以开发大量高级应用，提高数字化变电站的自动化程度。
Therefore, the electric power system needs a standard urgently of the open type transformer substation automation correspondence system.
因而，电力系统火急需求一个规范地开放式变电站主动化通讯系统。
A software reliability model for substation automation system based on improved JM model is set up in this paper.
因此在JM模型的基础上，提出了排错时间为负指数分布的软件可靠性模型及本模型的极大似然参数估计方法。
A software reliability model for substation automation system based on improved JM model is set up in this paper.
因此在JM模型的基础上，提出了排错时间为负指数分布的软件可靠性模型及本模型的极大似然参数估计方法。
应用推荐