The pure gum rubber sleeve of the Type A Valve offers excellent abrasion resistance, and since the Type A uses only air pressure to operate, there are no moving parts to break or wear out.
型夹管阀采用的纯树脂橡胶具有优异的抗磨损能力，因为A型夹管阀只是采用气压进行操作，因此没有活动部件会断裂或磨损。
Polyurethane film handily outperforms many other common polymers when it comes to abrasion resistance. Five times more resistant than natural rubber, the material is of choice of wear products.
聚氨酯薄膜的耐磨性胜过许多其他常见的聚合物。较天然橡胶耐磨五倍以上，是耐磨制品的首选材料之一。
Some high chromium steels can be hardened by heat treatment and are used where resistance to wear, abrasion, and corrosion are required.
一些高铬钢能通过热处理硬化，可用于抗磨坏，抗磨损，抗腐蚀需求的地方。
Good extreme pressure, abrasion resistance, reduce the tool wear, extending the service life of cutter.
良好的极压、抗磨损性能，减少刀具磨损，延长刀具寿命。
The effect of heating temperature on abrasion resistance of high alloy wear-resistant cast iron was studied.
研究了加热温度对高合金耐磨铸铁耐磨性的影响。
Wear resistance—The chip-tool and chip-work interfaces are exposed to such severe conditions that adhesive and abrasion wear is very common.
耐磨性—切屑-刀具与切屑-工件的接触界面处于如此严酷的状态，粘附和磨损是很普遍的。
The influence of varying impact energy on wear resistance of dual phase cast steel has been investigated under impact three body abrasion.
在动载三体磨粒磨损条件下，试验研究了冲击载荷的变化对铸态复相耐磨钢动载磨粒磨损特性的影响。
Bainite has higher abrasive wear resistance than tempered martensite with equal or higher hardness in hard abrasion, but in reverse in soft abrasion.
下贝氏体组织在高应力磨料磨损下比相同硬度，或稍高硬度的回火马氏体组织具有较高的耐磨性，但在低应力磨损下表现为不利的作用。
Wear resistance test shows that there is an increasing trend of resistance to abrasion with increase of laser energy.
耐磨性试验表明，随着能量的增加，耐磨性有提高的趋势。
Effect of microelement on the microstructure and wear resistance property of special brass have been investigated by SEM, abrasion machine etc.
利用电子探针、磨损试验机等试验手段，研究了微量元素对特殊黄铜的组织和耐磨性能的影响。
Its stabilizing effect and service life mainly depend on the wear-resistance ability of the abrasion-resistant alloy facing on the supporting wings.
它的稳杆效果和使用寿命主要决定于支撑翼堆焊耐磨合金的耐磨性能。
This article introduces the technology characteristics and coating functions of LX88A, as well as the abrasion and erosion wear resistance processes.
本文介绍了LX88A制取的工艺特点及涂层性能，并分析了类似于流化床作业面所经受的冲蚀磨损与磨粒磨损过程。
The effect of heating temperature on abrasion resistance of high alloy wear-resistant cast iron was studied.
采用金相、扫描电镜和力学性能分析方法研究了加热温度对含稀土低合金耐磨铸铁冲击韧性的影响。
Wear resistance of cake cutting knives using a special abrasion-proof material.
蛋糕切口刀子耐磨性使用特别磨蚀证明材料。
Excellent abrasion resistance to the extreme pressure to prevent rapid wear, prolonging the life of gears.
优良的极压抗磨性防止高速下磨损产生，延长齿轮寿命。
Effect of impact on wear resistance of high chromium cast iron and austenitic stainless steel has been studied by ball-on-ball impact and pin-on-disc abrasion test.
通过落球冲击和滑动磨损试验探讨了冲击对高铬铸铁和奥氏体不锈钢耐磨性的影响。
Particularly suitable for copper aluminium nickel materials and overlay welding on steel, increased resistance to wear and abrasion.
特别适用于铜铝镍材和钢材上的加层焊，加强抗磨损以及抗腐蚀性能。
AATCC rapid wear resistance tester, can rapid detection of textiles, paper, leather and plastic flexible material of dry, wet and abrasion resistance.
AATCC快速耐磨性测试仪，可快速检测纺织品、纸、皮革及塑料等柔性材料的干、湿耐磨性。
In addition to these features, particle swirl suppression ribs in the diffuser provide abrasion resistance by reducing the buildup of abrasives that can cause erosive wear.
除了以上提到的这些优点，每一级导流器都采用颗粒漩涡抑制技术，防止磨蚀性的颗粒漩涡形成，降低叶轮和泵体的磨损。
Timing belts are manufactured in thermoplastic polyurethane that gives superior wear and abrasion resistance.
同步带由热塑聚氨酯材料制成，具有较高抗磨损能力。
Timing belts are manufactured in thermoplastic polyurethane that gives superior wear and abrasion resistance.
同步带由热塑聚氨酯材料制成，具有较高抗磨损能力。
应用推荐