Impact abrasive wear is one of the worst conditions on abrasion.
冲击磨料磨损是一种极恶劣的磨损工况。
Abrasive wear may be defined as damage to a surface by a harder material.
磨粒磨损可定义为较硬的材料以一个表面的破坏。
Abrasive wear may be defined as damage to a surface by a harder material.
磨粒磨损可定义为较硬的材料对一个表面的破坏。
The main wear mechanisms are oxidation wear, adhesive wear, and abrasive wear.
主要磨损机制为氧化磨损、粘着磨损和磨粒磨损。
Its main wear mechanisms are plastic smearing, abrasive wear and fatigue spalling.
其磨损机理主要有塑性涂抹、磨粒磨损和疲劳剥落。
The abrasive wear resistance of the coating reduced when WC content was more than 25%.
当粉芯中WC质量分数超过25%后，涂层的耐磨性有所下降；
It favours the parts which is used to resisted the abrasive wear in severe impact work.
这对承受严重冲击的抗磨料磨损的机件来说，具有重要的意义。
The abrasive wear loss of the coatings was significantly influenced by particle temperature.
分析表明粒子的温度对涂层磨粒磨损质量损失有较大的影响。
It has been shown that fatigue spalling is the main wear mechanism, abrasive wear also exist.
结果表明，渗层磨损机制以疲劳剥落为主，兼有磨粒磨损。
Its comprehensive coverage focuses on key theoretical and practical considerations of abrasive wear.
它的广泛报导集中在磨损的关键理论和实践考虑。
The user can input, store, inquire and print the data of abrasive wear resistance materials by AWRMDS.
通过AWRMDS，用户可以输入、存储、查询和打印耐磨料磨损材料数据。
The micro-scale abrasive wear behaviors of TAMZ alloy were studied using a TE66 micro-scale abrasion tester.
采用TE66试验机对新型TAMZ钛合金的微磨粒磨损行为进行了研究。
The wear mechanism of the nanotube layers involved abrasive wear, fatigue wear, adhesive wear and oxidative wear.
纳米管层的磨损机理主要为磨粒磨损、疲劳磨损、粘着磨损和氧化腐蚀磨损。
There are five forms of wear and wear: abrasive wear, erosive wear, adhesive wear, fatigue wear and corrosive wear.
磨损有五种磨损形式：磨料磨损、冲蚀磨损、粘着磨损、疲劳磨损和腐蚀磨损。
Two typical failures of abrasive wear and cracks for the hook head were studied, and its mechanisms were discussed.
对钩舌产生的两种典型失效形式—磨损和裂纹进行了详细观察，并对其形成机理进行了探讨。
Simulating test and vibration signal analysis for abrasive wear failure of rollings bearings have been made in this paper.
对滚动轴承磨粒磨损故障进行了模拟试验和振动信号的处理和分析。
The wear mechanism was abrasive wear and adhesion transfer of the counter-parter when the volume content of PTFE was high.
当PTFE含量较高时，磨损机理除了磨粒磨损外还有对偶件的粘着转移。
Based on the principle of wheel-rail interaction, the mechanism of the abrasive wear damage of wheels and rails is studied.
运用轮轨相互作用原理，研究轮轨磨耗伤损的机理。
The wear resistance of casting composite medium manganese steel has been studied under the condition of impact abrasive wear.
研究了铸造复合中锰奥氏体钢在冲击磨料磨损条件下的耐磨性能。
The X-ray diffraction was used to determine the structure of the coating surface. At last, the shock abrasive wear test was performed.
用X射线衍射分析方法测定了镀层表面结构并作了冲击磨料磨损试验。
Moreover, the coatings with comparative lower abrasive wear rate can be deposited in the condition of moderate flows of oxygen and propane.
氧气流量、燃气流量适中的条件下制备的涂层磨损率较低。
In this paper, the research works on the wear of polymers are reviewed, mainly in the aspects of sliding wear, abrasive wear and erosive wear.
本文综述了近年来国内外学者在高分子材料磨损方面的研究工作，着重阐述了滑动磨损、磨粒磨损、冲蚀磨损的研究进展。
It is shown that the flows of both propane and oxygen and spray distance have an interaction on the abrasive wear performance of the coatings.
结果表明：氧气流量、燃气流量和喷涂距离对涂层磨粒磨损性能具有交互影响。
The SB series impeller is designed to allow fluid leaving the impeller to blend with recirculating fluid to reduce abrasive wear of the casing.
该叶轮的设计允许从叶轮出来的液流与回液混和以减小泵的磨损。
The abrasive wear, fatigue wear and adhesive wear are the main factors causing the excess wear and breaking of the driving chain on drilling RIGS.
磨料磨损、疲劳磨损和胶合等是引起石油钻机传动链条磨损超限，承载；能力降低，最后导致链条断裂破坏的主要原因。
Bainite has higher abrasive wear resistance than tempered martensite with equal or higher hardness in hard abrasion, but in reverse in soft abrasion.
下贝氏体组织在高应力磨料磨损下比相同硬度，或稍高硬度的回火马氏体组织具有较高的耐磨性，但在低应力磨损下表现为不利的作用。
Impact abrasive wear behavior of electroless Ni-P coating was researched by means of single-pass pendulum scratching test characterized by impact loading.
利用单摆划痕法的冲击加载特性，研究了N i - P化学镀层的冲击磨粒磨损性能。
The impact abrasive wear resistance of materials and its fatigue wear mechanism under the conditions of quartz and coal as abrasive had been investigated.
研究了石英和煤两种磨料条件下材料的冲击磨料磨损耐磨性及其疲劳磨损机制。
The impact abrasive wear resistance of materials and its fatigue wear mechanism under the conditions of quartz and coal as abrasive had been investigated.
研究了石英和煤两种磨料条件下材料的冲击磨料磨损耐磨性及其疲劳磨损机制。
应用推荐