The paper provides a scheme to control AC servo-motor using single chip-computer AT89C51, including hardware design and software design.
介绍了一种由at89c 51单片机控制交流伺服电机的系统方案，包括系统硬件设计和软件设计。
The fed length of insulating sleeve and heat printing paper were respectively controlled by an AC servo-motor and a stepping motor in the machine.
该设备利用伺服和步进驱动实现套管带和烫印纸的定长传送；由气缸控制套管烫印头与裁切刀具的运动；
Ac servo system in many performance is better than the stepping motor.
交流伺服系统在许多性能方面都优于步进电机。
Adopting ac servo motor as the driving device, can the dc servo motor and a high precision, high performance as the half closed loop or closed loop control system.
采用交流伺服电机作为驱动器件，可以和直流伺服电机一样构成高精度，高性能的半闭环或闭环控制系统。
Now commonly used servo motor is ac servo motor, the axial end in motor with photoelectric encoder, by examining the rotor Angle to frequency conversion control.
目前常用的伺服电机是交流伺服电机，在电机的轴端装有光电编码器，通过检测转子角度用以变频控制。
Ac servo system in many performance are better than the stepping motor.
交流伺服系统在许多性能方面都优于步进电机。
In the meantime, by using an AC servo motor as the driving parts and based on the MPC02 motion control card, the open control system was formed.
同时采用交流伺服电机作为驱动元件，基于MPC02运动控制卡作为上位控制单元构建了开放式控制系统。
Aiming at characteristics of unpredictability the load torque used in ac motor servo system, a method of load torque adaptive identification based on state observer is presented.
针对交流电机伺服系统中负载转矩不可预测性的特点，提出一种基于状态观测器的负载转矩自适应辨识方法。
The paper introduces the hardware and software design of an AC servo motor control card based on 80C196KC.
介绍自行研制的基于80C196KC单片机的交流伺服电机控制卡的硬件设计及其软件实现。
SVC(TND)SERIES single phase high precision full automatic ac voltage regulator composable of contact auto voltage regulator, servo motor automatic control circuit etc.
系列单相高精度全自动交流稳压器，由接触式自耦调压伺服式电动机、自动控制电路等组成。
The cam controller allows the AC servo motor to run at different speed for different angles, and to turn on and turn off twi.
设计的凸轮控制器可实现对AC伺服电动机进行分段变速控制以及凸轮一周中的两通两断的控制功能。
Adopting ac servo motor as a drive device, can and dc servo motor as a high precision, high performance and a half closed loop or closed loop control system.
采用交流伺服电机作为驱动器件，可以和直流伺服电机一样构成高精度，高性能的半闭环或闭环控制系统。
A new sensorless control method for AC permanent magnet linear servo motor using a sliding mode observer is proposed in this paper.
提出了一种采用滑模观测器的交流永磁直线伺服电机无传感器控制的新方法。
The whole project design of the AC servo motor control system based on TMS320F2812 is introduced.
介绍了基于TMS320F2812交流伺服电机控制系统的整体方案设计。
Commonly used servo motor is ac servo motor, the motor shaft with in the photoelectric encoder, by detecting the rotor Angle to frequency conversion control.
常用的伺服电机是交流伺服电机，在电机的轴端装有光电编码器，通过检测转子角度用以变频控制。
This paper introduced how to use digital ac servo motor in the universal material testing machine, and give an example of applying MINAS a serial servo motor to 5 tons material testing machine.
主要介绍了全数字式交流伺服电机在万能材料试验机控制系统中的应用，并给出了将松下MINASA系列伺服电机用于5吨材料试验机的例子。
The article introduced the composition, the main characteristics and the control principle of the ac servo motor control system as well as points for attention in the system debugging process.
介绍交流伺服电机控制系统的组成、主要特性、控制原理及在系统调试过程中应注意的事项。
This paper deals with an AC servo system with permanent magnetic brushless motor driven by square wave current.
研究了方波电流驱动的永磁无刷电机交流伺服系统。
The feed drive system of a precision cold ring rolling mill adopts AC servo motor and mechanical transmission, rather than conventional electro-hydraulic actuator.
采用交流伺服电机和机械驱动进给系统的冷轧环机，其进给伺服控制系统的设计需要一个新的工艺动力学模型。
Due to the ac servo motor is in brushless structure, almost does not need to repair, the volume is relatively small, be helpful for the improvement of speed and power.
由于交流伺服电机内是无刷结构，几乎不需维修，体积相对较小，有利于转速和功率的提高。
Permanent ac servo motor control system of lockstitch sewing machine is introduced.
介绍了一种用于电脑全自动工业平缝机的永磁交流伺服电机及其控制系统。
Feed transmission: using AC servo motor to drive the precise ball screw sets that supported by special ball screw bearing, which improves the rigidity and precision of feed movement.
进给传动：三向进给均采用交流伺服电机驱动精密滚珠丝杆，专用丝杆轴承支承，提高了机床的进给运动刚性和精度。
In this paper a new control strategy suited for AC servo system of permanent magnet AC motor is introduced.
本文介绍了一种适用于正弦波永磁同步伺服系统的控制策略。
Machine tool feed system is usually driven by ac servo motor ball screw feed drive to achieve, to simplify the structure.
机床的进给系统通常是通过交流伺服电机驱动的驱动滚珠丝杠饲料，简化结构，实现。
Travelling control system is composed of a transducer, an AC servo motor, an optical encoder and other components, which achieves precise control of the movable bench's position.
通过变频器、交流伺服电机、行程光电编码器等设备组成了行程控制系统，实现了可移动台架位置的精确控制。
This paper introduces how to control SCARA by PMACLITE motion controller. It expatiates how to tune AC servo motor and create track of SCARA based on PMAC.
介绍如何实现PMAC LITE四轴运动控制器对SCARA机器人的控制，具体阐述了基于PMAC下，交流伺服电机的调整以及SCARA机器人轨迹的生成。
The full digital technique was adopted to realize the servo control of the ac permanent-magnet synchronous (motor.) the technology was applied in the industrial sewing machine.
采用全数字技术实现对交流永磁同步电机的伺服控制，并将此项技术应用于工业缝纫机领域。
The full digital technique was adopted to realize the servo control of the ac permanent-magnet synchronous (motor.) the technology was applied in the industrial sewing machine.
采用全数字技术实现对交流永磁同步电机的伺服控制，并将此项技术应用于工业缝纫机领域。
应用推荐