Automatic pressure relief during annealing process.
在退火过程中自动进行泄压。
The alloying annealing process of zinc layer is also described.
并对锌层合金化退火工艺进行了阐述。
In the third chapter, we discuss the annealing process on the Euclidean space.
第三章，我们考虑了欧氏空间上的退火过程。
The spheroidizing annealing process of MC5 cold roll steel has been studied in detail.
详细研究了MC 5轧辊钢球化退火工艺。
And, the annealing process release the stress of the films, which give the film a higher density.
退火使薄膜的折射率将低，释放膜层中的应力，膜层结构更加致密。
The annealing process of centrifugal ductile cast iron pipe by the heated mould method is studied.
研究了热模法离心铸造球铁管的退火工艺。
PLZT thin film without intermediate pre-annealing process displays (100)-preferential orientation.
没有中间温度预退火过程的薄膜，显示出（100）择优取向；
Local optimal algorithm against the shortcomings, I was prepared simulated annealing process improvements.
针对算法局部最优的缺点，本人正在编制模拟退火程序进行改进。
The study on the annealing process and specture character for copper-exchanged waveguide is also discussed.
另个，还对制备的波导进行了一些光学和物性的测试。
The results show that the intermediate pre-annealing process can affect the selection of crystalline texture.
结果发现，中间温度预退火过程可以影响薄膜对晶型结构的选择。
In addition, the annealing process of SiC films is mostly carried out in vacuum, argon gas or nitrogen gas ambience.
另外，对碳化硅薄膜的退火处理大多是在真空、空气、氩气或氮气气氛下进行。
Based on ternary model method, the mathematical model of strip steel annealing process in vertical furnace is built.
以三元模型法为基础，建立了带钢在立式炉内退火全过程的数学模型；
We employ the magnetic sputtering method to deposit amorphous tungsten films and investigate their thermal annealing process.
对使用磁控溅射法沉积的钨薄膜进行了热退火研究。
After hot rolling, only through full recrystallizing by annealing process in the batch, can the stainless steel be put into use.
不锈钢经过热轧后，需经罩式炉退火工艺使材料充分再结晶后才能投入使用。
We use the total annealing process on the welding of end plate and body, to prevent the stress and deformation incurred by welding.
采用国际领先的制造工艺，端板与桶体的焊接加工均采用整体退火处理，防止焊接后的“应力变形”；
During designing stable temperature field and selecting rational technology parameter and annealing process, perfect crystal was grown.
可通过设计合理而稳定的温场，选择最佳工艺参数及退火处理等方法，减少热应力而引起的晶体开裂。
In 2005, a postdoctoral researcher in his laboratory developed a water annealing process, reconstituting the silks slowly in a humid environment.
2005年，他实验室的一位博士后研究员利用一种水退火过程在潮湿环境下对丝类进行了缓慢的重组。
In different coefficient of thermal conductivity, two kinds of finite element model were used to simulate and solve for the annealing process.
在不同导热系数条件下，采用两种有限元模型对退火过程进行模拟和求解。
The affection of different annealing process conditions on TiN film stress is also researched, low temperature annealing of film can be realized.
论文还研究了不同退火工艺条件对薄膜应力的影响，可以实现薄膜低温退火。
The annealing process was made under different temperature and holding time to the cold forging AZ31 magnesium alloy with different deformation ratio.
对不同变形量的冷锻az31镁合金在不同温度和保温时间下进行退火。
Basing on the heat transfer mathematical models and the simulation system, the temperature fields of coils during annealing process have been calculated.
并结合对钢卷导热方程和边界条件的离散求解，实现了钢卷温度场模拟计算的同时，获取了全氢炉退火过程的工艺制度。
However, during hot rolling, cooling and annealing process, a complex oxide structure layer will form on the surface of stainless steel due to oxidation.
但在热轧、冷却及退火等过程中，不锈钢工件的表面因氧化会产生一层结构比较复杂的氧化皮。
In continuous annealing process, strip tension is an important factor that decides whether the continuous annealing line works steadily and promptly or not.
在带钢连续退火过程中，带钢张力的波动是造成带钢产品质量下降及制约连续退火机组高速运行的重要原因。
Annealing process is the key process to ensure the quality of stainless thick wall pipe. The improper operation and adjusting will induce the quality problem.
不锈钢薄壁焊管退火(固溶处理)是保证产品质量的关键工序，在实际生产中如操作和调整不当都会出现质量问题。
The effect of batch annealing process on the microstructure and mechanical properties of SPCCSD cold rolled steel sheet was studied under laboratory conditions.
在实验室条件下，研究了罩式退火工艺对SPCC- SD冷轧板组织和性能的影响。
The principle of the cooling of copper conductors during the continuous annealing process is presented. The law for the cooling process was deduced theoretically.
该文讨论了电线电缆生产中导线连续退火装置冷却过程的工作原理，从理论上导出了冷却过程所遵循的规律。
The numerical value model of thermal conduction was established for annealing process of aluminium foil coils based on annealing furnace loaded with 40 t capacities.
以40t铝材退火炉内铝卷为研究对象，建立了铝卷退火过程的导热数值模型。
Wafer pairs with bonding interface being native oxide or thermal oxide have different bonding behavior in the annealing process, which were investigated and compared.
将硅本征氧化层与硅热氧化层两种键合界面在退火过程中的行为进行了理论分析与比较。
Wafer pairs with bonding interface being native oxide or thermal oxide have different bonding behavior in the annealing process, which were investigated and compared.
将硅本征氧化层与硅热氧化层两种键合界面在退火过程中的行为进行了理论分析与比较。
应用推荐