The body of valve for Electronic Throttle Control(ETC) is an example among them.
汽车电子节气门控制（ETC）的阀体就是其中一例。
Caution: the sealing surface for the diaphragm on the top flange of the valve body receives special factory preparation to enhance sealing with PTFE diaphragms.
警告：用于阀体法兰上的隔膜的密封面在工厂受到特殊的处理，以强化聚四氟乙烯隔膜的密封性能。
Thoroughly clean all inside surfaces of the relief valve body.
彻底清洗安全阀阀体的所有内部表面。
Slide one half of the splash guard into the groove on the relief valve body.
将防溅保护的一半滑动到安全阀阀体的沟槽上。
Beneath the handwheel is one set of wrench flats on a nut threaded into the valve body. This is the diaphragm-retaining nut.
在手轮下面，在一个旋进阀体的螺母上面是一套扳手面。这是横膈膜止动螺母。
Install the Watts regulator in the supply line to the boiler with the arrow on the valve body pointing in the direction of flow to the boiler.
在锅炉的供水管道上安装美国瓦茨调节阀，将调节阀阀体上的箭头指向锅炉的水流方向。
Shipbuilding . head of sounding pipes with self - acting valve . details of body.
造船工业。带自动阀的测深管测头。阀体详图。
Regulation in a number of institutions under the valve cover as part of the body is not separated.
在一些调节机构中下阀盖作为阀体的一部分，并不分离。
The hand wheel is always in the same position relative to the valve body regardless of whether the valve is in the open or closed position.
不管阀门是在开启或是关闭位置，手轮总是处在相对于阀体的同样的位置。
The valve seat of the integrative type, the valve body, valve seat connection question exist.
一体式的阀座，不存在阀体、阀座连接问题。
Pay attention to the flow direction of medium and install the valve referring to the indicating arrow on the valve body.
安装时请认清介质流向并按阀体上指示箭头方位正确安装。
Any kind of valve body can forging, also can cast, should according to the requirements of users and manufacturers owned manufacturing methods.
任何一种闸阀阀体即可锻造，也可铸造，应根据用户要求以及制造厂拥有的制造手段而定。
If the valve body material can be welded, but very different thermal expansion coefficient, or changes in operating temperature range of a larger thread junction closure weld must be honey.
如果阀体的材料是可以焊接的，但膨胀系数差异很大，或者工作温度的变化幅度范围较大，螺纹连接部必须进行蜜封焊。
Exchange the sealing ring of the valve body according to the working condition of rubber sealing ring in order to ensure the sealing performance.
按橡胶密封圈使用性能，根据具体情况定期对阀体的密封圈进行更换，以保证阀门的密封性能。
Valve body shall be drilled and tapped for a pressure connection on top and bottom of the housing.
阀体应该钻孔和攻丝用于在顶部和底部外壳的压力连接。
The valve inlet and body are one integral casting assuring proper alignment of disc, seat and spindle for smooth action.
这种阀门的进口和阀体为一件式铸件，确保了阀瓣，阀座和芯轴的对齐和平稳运动。
The check valves shall be modular and shall seal to the main valve body by the use of an O-ring.
这种止回阀应该是模块化的，并且应该采用一个O形环密封在主阀体上。
In some regulatory agencies as the lower body Gate Valves part of the valve cover, not separation.
在一些调节机构中下阀盖作为阀体的一部分，并不分离。
The valve is mainly made up of body, disc, axle, rocker and heavy hammer etc. It realizes discharging and air locking using trimming moment.
重锤锁气翻板卸灰阀主要由阀体、阀板、阀轴、摇杆、重锤等零件组成，利用力矩平衡的方法实现锁气卸灰。
According to the structural feature of parallel single disk gate valve, the strength and rigidity of body will be calculated with finite element method, and with cylindroid shell theory.
根据主闸阀结构特点，分别用有限元法和椭圆柱板壳理论公式计算了阀体的强度与刚度，并进行了分析对比，同时对闸板的刚度进行了校核。
Install with the arrow on valve body pointing in the direction of flow.
安装时要使阀体箭头指向水流方向。
Apply heat with flame directed away from the center of the valve body. Excessive heat can harm the seats.
在用明火加热时不要直接施加在阀体中心上。过热可能损害阀座。
This paper introduces the manufacture of sealing surface (valve body) about great size check valve and analyzes the choices and the decisions about geometrical parameters of tools.
介绍了大口径止回阀阀体密封面的加工方法，分析了刀具几何参数的选择与确定。
Smooth operation of throttle linkage and throttle body air valve.
节流连杆和节流体空气阀的平稳操作。
The flow control valve is mainly made up of housing, body, sealing shim, liner bushing, valve cartridge, bearing, breather layer, aerator tank and transmission device etc.
流量控制阀主要有机座、阀体、密封垫、衬套、阀芯、轴承、透气层、充气槽及传动装置组成。
The flow control valve is mainly made up of housing, body, sealing shim, liner bushing, valve cartridge, bearing, breather layer, aerator tank and transmission device etc.
流量控制阀主要有机座、阀体、密封垫、衬套、阀芯、轴承、透气层、充气槽及传动装置组成。
应用推荐