The only connection you can make with this device is a slave connection on the OPB; click in the leftmost white bus square to establish this connection (a lowercase 's' will appear in the box).
用这个设备能实现的唯一连接就是在OPB上的从连接；请在最左侧的空总线框中单击，建立此连接(框内会出现一个小写的“s”)。
The objective of the research is to design a multifunctional and universalizable slave interface for PROFIBUS DP, so an ordinary device can be connected on this bus conveniently.
本课题旨在为PROFIBUSDP这一特定总线，设计一款通用的多功能从站接口，从而使普通的设备可方便的挂接到总线上。
In distributed measurement and control system with bus structure, master slave communication may be replaced by race communication, when real time and burst are needed.
在总线结构的分布式测控系统中，当系统实时性要求较高、突发性较强时，主从通信方式往往不能适应需要，而需要采用竞争式通信。
In the design of column readout stage, master and slaver structure has been adapted, where master amplifier converts charge to voltage, and slave amplifier works with standby mode to drive output bus.
列读出级采用新型主从两级放大列读出结构，其中主放大器完成电荷到电压的转换，从放大器驱动输出总线来满足一定的读出速度。
Single bus technology is a master-slave network with data communication by both a data line and a return line.
单总线技术是使用一根数据线与一根返回线实现数据通信的主从式网络。
As the basic SoC design technique, the AHB bus interface design consists of master module interface design and slave module interface design.
AHB总线接口设计划分为主控模块接口设计及从模块接口设计。
For VME bus, users themselves could design interface circuit according to particular demand such as only slave interface.
对于VME总线，用户可以根据特定要求自行设计接口电路，比如只实现从模块访问。
The connection between the host and the slave intellectual meters is the CAN field bus net communication block SJA1000, and the meters as slave are placed on the industry spot.
采用CAN总线网络通信模块SJA1000实现监控主站与底层智能仪表的连接，而仪表作为从站放置在现场。
PROFIBUS DP is a kind of multi master-slave station structure bus, and the communication between the masters is Token way, and subordination between the master and slaves.
PROFIBUSDP是一种多主从总线，采用主站间按令牌方式、从站和主站间按主从方式进行数据通信的工作方式。
The proposal based on USB Host/Slave controller chip CH375A, realized a USB-Host embedded in CAN bus data acquisition system and stored acquisition data of each node in U flash disk under MCU control.
该方案基于USB主/从控制芯片CH375A，在单片机的控制下，实现了CAN总线数据采集系统中嵌入USB主机，从而完成把各节点采集的数据存入U盘，取代了现场数据采集系统必须有一台计算机的模式。
The proposal based on USB Host/Slave controller chip CH375A, realized a USB-Host embedded in CAN bus data acquisition system and stored acquisition data of each node in U flash disk under MCU control.
该方案基于USB主/从控制芯片CH375A，在单片机的控制下，实现了CAN总线数据采集系统中嵌入USB主机，从而完成把各节点采集的数据存入U盘，取代了现场数据采集系统必须有一台计算机的模式。
应用推荐