Provide welding neck flange butt welding required for the purpose of the right pad with neighboring component.
提供焊接法兰的脖子上对接焊目的所需要的正确垫与邻近组成部分。
In the process of DC upset butt welding, the joint quality was strongly effected by the temperature distribution in the direction of the plate width.
板材直流电阻对焊过程中，对接端面沿板宽方向的温度分布对焊接接头的质量有很大的影响。
It shows by the process that the equipment can meet the requirements of flashing butt welding.
工艺试验表明，该设备能实现脉冲闪光对焊的要求，焊接接头能够满足使用要求。
According to the plate butt welding of A105 steel, the transverse deformation was real-time measured during welding.
通过A105钢的平板对接试验，对焊接过程中焊接横向变形进行实时测量。
The joint deformation of DC upset butt welding was studied by using theory of plastic deformation and rigid-viscosity plastic material model.
采用塑性变形理论和刚粘塑性材料模型研究了直流电阻对焊接头的塑性变形。
A displacement threshold was used to control DC upset butt welding process, and constant pressure and varied pressure tests were carried out on Q235 a steel strips.
采用位移门槛电压控制焊接过程，对Q 235 - A钢进行了变压式和等压式扁钢带直流电阻对焊试验。
Therefore the general construction process scheme is worked out as follows: open trench drainage, work site dried in the sun, conventional butt welding, and pipe laid down into trench.
经过调研和反复现场勘察，确定的总体施工方案为：挖明沟排水，作业带晾晒，正常组对焊接，沉管下沟。
The key of Cu-Al pipe butt welding is to control the welding parameters. In the original control system, all welding parameters were controlled by time-relays.
铜铝管焊接的关键是对焊接参数的控制，原控制系统采用时间继电器控制焊接参数。
In this paper, on the base of the study of flash butt welding theory, a new intelligent control system of rail flash butt welding is developed.
本文基于闪光焊接理论研究及钢轨闪光焊接的工艺要求，设计了一种智能控制的钢轨闪光焊焊接系统。
BT20 titanium alloy is welded with butt welding on GTAW machine... Experiment of plastic deformation is done on press and double heat preservation measure is used during plastic deformation.
试验采用钨极氩弧焊对接焊形式对BT 20钛合金施焊；焊接接头的塑性变形试验在油压机上进行，变形过程中采用了双保温措施。
According to the actual situation of Guangdong province township shipyard, Introduction to butt welding and fillet welding procedure approval process and technical standards and the note.
结合广东省乡镇船厂实际，介绍钢板对接焊和角接焊的焊接工艺认可流程、技术标准和有关注意事项。
Based on the operating principle of magnetically impelled rotating arc, a new type of tube to plate butt welding device was designed.
根据磁控旋转电弧的工作原理，设计了一种新型磁控旋转电弧管板对焊装置。
The Intellectual Control System of Flash Butt Welding, the main and basic part of the Flash butt welding machine, is the basic to realize the automation of the welding process.
基于模糊控制的智能化闪光焊机控制系统是闪光焊机焊接系统的重要组成部分。
Flash impetus and adopting projection anulus controlling upsetting, steady speed flash and quality of butt welding point is well.
闪光推进和顶锻采用凸轮控制，闪光速度平稳对接焊口质量好。
A reliable way to improve the quality of spiral pipe was the substitution of high frequency butt welding for HF lap welding.
高频对焊代替高频搭焊是提高中直径螺旋焊管质量的可靠途径。
Butt welding machine process was introduced. 8031 single chip computer was used in controlling flashing current. Hence the flashing butt welding process automation is so achieved.
本文介绍了对焊机的生产工艺过程，并采用8031单片机对闪光电流控制，从而使闪光对焊工艺实现了自动化。
Comparison between radiographic and ultrasonic detection of butt welding on gas pipelines is made in this paper, and some advantages and shortcomings of these methods are analyzed.
对射线、超声和超声波成像几种检测方法检测管道焊缝的优缺点进行比较，对超声波配合超声成像检测现行管道焊缝的可行性进行了探讨。
The principle, applications and process of TANDEM double wire welding for butt welding in shipbuilding were introduced.
介绍了TANDEM双丝焊在造船拼板焊接中的原理、应用和工艺。
The welding technology used for preheating flash butt welding was evaluated for workpieces with large welding section.
针对大截面工件的闪光对焊工艺特点，确定了预热闪光焊的焊接工艺。
Groove preparation, cleaning before welding and butt welding construction of ther tower were showed.
介绍了坡口加工、焊前清理和上下塔对接施焊进程。
In this paper, the defects appeared in flash butt welding for HSS cutting tools have been analyzed. And the effective resolving way has been put forward.
本文对高速钢刀具闪光对焊经常出现的主要缺陷问题进行了具体分析，并提出了有效的解决措施。
It successfully applies the real time control of welding procedure process on large power flash butt welding complete equipment.
成功地用于大功率闪光对焊成套设备的焊接工艺过程实时控制。
The quality of cutting can meet the requirement of subsequent laser butt - welding.
切缝质量可以满足随后激光拼焊的要求。
Studied the joint structure and properties of flash butt welding to mining chains round made of new type meta-bainite steel.
研究了新型准贝氏体钢制造的矿用圆环链闪光对焊焊缝的组织与性能。
The fatigue and ultimate strength analysis of hull structure with two different butt-welding lines distribution was researched in this paper.
对两种不同对接焊缝布置下的船体结构进行疲劳强度和极限承载能力分析。
The whole procedure includes preparing steel strip and butt welding, forming and fixed position welding, pipe output and cutting, and final submerged arc welding.
其整个工艺包括带钢准备和对接、成型及定位焊、管子输出和切割和埋弧终焊。
This paper, based on analyzing the process of Cu-Al pipe butt welding, discussed the design of the executive system and control system for PLC controlled Cu-Al pipe butt welder.
在分析了铜铝管焊接工艺过程的基础上，重点论述了铜铝管对焊机执行系统和控制系统的设计。
The experiment result proved the technological feasibility of laser butt welding for thin zinc coated steel sheets whose edges are prepared by laser cutting on the same laser processing equipments.
试验结果表明，镀锌板的激光剪裁拼焊接头性能符合实际使用要求，在同一台激光加工设备上实现镀锌板的激光切割剪裁后再直接进行激光拼焊的工艺方法是可行的。
There are four phases and dozens of parameters in preheating flash butt welding technology used for great section workpiece's welding.
用于焊接大截面工件的预热闪光焊工艺包括四个阶段。
When ordering Butt Welding End valves, specify schedule of pipe end and give complete data concerning style, figure number and contour of weld end.
在订购对焊连接阀门时，要指定管道连接端口的管壁厚度，并且提供有关类型、型号和焊接端等高线等参数。
应用推荐