The combustion chamber pressure and propulsive force were tested.
该项研究主要测量了发动机的推力和燃烧室压力。
The fan component is produced using cold chamber pressure die casting process.
风机部件的创造采用冷腔室压力拉模铸造工艺。
Simply type a chamber pressure and observe the new stable vacuum in less than a minute.
简单的输入腔室压力，一分钟之内可以看到新的稳定的真空。
The effection and methods of controlling chamber pressure in heating furnace are narrated.
论述了加热炉炉膛压力控制的作用、控制方法。
The conditions to realize automatic control of chamber pressure in heating furnace are concluded.
给出了实现加热炉炉膛压力自动控制的条件。
Input is simply a list of propellant ingredients, as well as chamber pressure and nozzle exit pressure.
投入，简直是名单推进剂成分，以及商会的压力和喷嘴出口的压力。
The meaning of quasi dynamic calibration of copper balls using to measure artillery chamber pressure is presented.
介绍了火炮膛压测压铜球准动态校准含义，分析了引起准动态校准压力对照表编表误差的因素。
The results indicate that the exergy loss reduces with the chamber pressure rising during the primary drying period;
计算结果表明：随着干燥室压力的增大，物料的损失减小；
The effects of combustion chamber pressure and mixture ratio on engine performance were analyzed based on simulation.
并根据结果分析了燃烧室压强和混合比对发动机性能的影响。
These include: shelf temperature, product temperature, condenser temperature, chamber pressure and condenser pressure.
包括：板层温度、产品温度、冷凝器温度、前箱压力、冷凝器压力。
The effects of chamber pressure variations under high and low ranges on film microscopical composition actions are different.
高、低反应气压变化对膜内微观组分影响有异；
The model predicts the transient variations of gun chamber pressure, projectile motion and the decomposition rate of propellant.
模型可以预测发射过程中药室内压力、弹丸运动及工质的分解速率的瞬时变化。
Otherwise if the chamber pressure is low, the product is pumped away the chamber in time, and there is no polymer on the surface.
当腔体压力较低时，生成物被及时带走，则样品表面光亮，无聚合物残留。
The air chamber pressure mod el created and the flow coefficients obtained are references for air pressure ABS control logic design.
建立的气室压力模型和所求得的流量系数为气压abs控制逻辑的设计提供了依据。
A new modular method for calculating the maximum combustion chamber pressure with stage combustion cycles is proposed in this paper.
提出了一种新的液体火箭发动机分级燃烧循环最高室压计算方法。
Nevertheless, particle size distribute does not change with the combustion chamber pressure and propellant aluminum powder percentage.
粒子尺寸分布不随燃烧室压强和推进剂铝粉含量变化。
The influence of chamber pressure, gas flow rate and RF power on micro loading effect in reactive ion etch of silicon dioxide is researched.
对二氧化硅反应离子刻蚀中反应室压力，刻蚀气体流量和射频功率等因素对刻蚀速率和刻蚀均匀性的影响进行了研究。
The charge utilization ratio is high for multi-point ignition tube experiments in a high-pressure gun, but the chamber pressure wave is high.
某高膛压火炮试验中发现多点点火方案的装药利用率较高，但膛内压力波较大。
The effect of pressurized air supply system in the stairwell and pre-chamber pressure is better and can satisfy to the evacuation requirements.
对楼梯间和合用前室分别进行加压送风效果较好，能够满足疏散要求。
The results show that the effect of combustion efficiency on chamber pressure is limited, nozzle loss is mainly caused by its structure and size.
研究表明，补燃室压强的变化对燃烧效率的影响是有限的，喷管损失主要与喷管结构尺寸有关；
Basing on the test results, the influences of chamber pressure and shelf temperature on sublimation rate and sublimation temperature are studied.
通过实验，研究了冻干过程中干燥箱内压力和搁板温度对升华速度及升华温度的重要作用。
The stable condition of equilibrium pressure and the approximate relationship between the chamber pressure and the equilibrium pressure are derived.
然后，简略地证明了平衡压力的稳定条件以及燃烧室压力与平衡压力的近似关系。
The effects of both chamber pressure and initial Porosity on combustion process are calculated, and some basic conditions for stable burning are analysed.
计算了燃烧室压力与初始空隙率等对燃烧过程的影响，分析了稳定燃烧时应满足的一些基本条件，结果与实验值相一致。
Thermal analysis on the thermopneumatic pump to be used in the PCR chip is performed to understand the relation between chamber pressure and temperature field.
对热气动式微泵进行了热分析，得到了泵室压力与温度场的关系。
But because the chamber pressure of this gun is high, the deformation of the steel cartridge case is enlarged, and the extraction ratio cannot reach the standard.
但由于该炮膛压较高，使得钢质药筒的变形加大，不抽筒率超标严重。
Thee design of the C-400 is very similar to that of the B-200 motor, being slightly larger in size, and operating at a somewhat higher chamber pressure (greater Kn).
设计的C- 400非常相似，这对B - 200型汽车，被稍大的大小，和经营一个较高的压力，会议厅（更大的千牛） 。
This paper presents the development of the liquid propellant rocket engine technology from the viewpoint of combustion chamber pressure, thrust level and power cycle.
本文从燃烧室压力、系统工作循环方式以及最大推力三个方面叙述了世界各国液体火箭发动机的技术水平。
The motor was installed and adjusted to allow free vertical movement, connections to the chamber pressure measuring system were made, and the oil buffer system was filled.
电机的安装和调整，以允许自由垂直运动，连接到会议厅的压力测量系统发了言，和石油的缓冲系统填补。
The motor was installed and adjusted to allow free vertical movement, connections to the chamber pressure measuring system were made, and the oil buffer system was filled.
电机的安装和调整，以允许自由垂直运动，连接到会议厅的压力测量系统发了言，和石油的缓冲系统填补。
应用推荐