The coefficient of convection heat transfer increases with increasing the particle diameters.
对流换热系数随着颗粒直径的增大而增大。
The results showed that the intensity distribution had relation with the velocity of percolation, time, coefficient of convection and diffusion.
发现污染物在土壤中的质量浓度分布与渗流速度、作用时间、扩散系数等有关。
Using alternating segment explicit implicit method for the variable coefficient convection diffusion equation. The method has the obvious property of parallelism and is unconditionally stable.
应用交替分段显隐方法求解变系数对流扩散方程，此方法具有很好的并行性且无条件稳定。
This makes the convective heat transfer coefficient of the stainless steel tube is larger than that of the convection heat transfer coefficient of the copper tube.
这就使不锈钢管的对流放热系数比铜管的对流放热系数大。
However, the more consummately method should confirm the convection coefficient of heat-side and cold-side liquid, so as to find out the problem and to ameliorate it.
然而，更完善的办法应该是同时再确定换热器冷、热两侧流体的对流换热系数，以便找出问题所在并进行改进。
Local convection heat transfer coefficient decreases along the micro-tube by 12.5% for the influence of thermal conductivity of liquid nitrogen.
微通道中局部对流换热系数受到液氮导热系数变化的影响沿管程逐渐下降约12.5%。
General heat release coefficient is used to equivalently consider autoclave radiation and convection of boundary condition during curing process for CFRP pressure vessel.
文中应用总放热系数等效考虑了CFRP压力容器固化过程中热压釜辐射与对流边界条件。
The coefficient can be indicative of the material abrasion resistance properly and directly used to calculate the safety gas velocity in the convection heating surface of coal-fired boilers.
并用它表征塑性材料的抗磨性能。该系数可直接应用于计算燃煤锅炉对流受热面的安全烟速。
The study is about the coefficient of heat transfer of convection in the stage of Constant rate of drying with the ways of dimensional analysis and the experiments.
应用因次分析和实验测定相结合的方法，对恒速干燥阶段的对流传热系数进行了研究。
The test results indicate that there is linear relationship between surface convection coefficient of concrete and wind velocity.
结果表明，混凝土表面对流换热系数与风速基本呈线性关系。
The convection heat transfer coefficient of coolant within the grinding zone has been estimated using hydrodynamic and thermal modeling.
磨削区冷却液的热对流系数已由流体动力学和传热学模型估算得到。
Method and formulae for calculating the mean forced convection heat-transfer coefficient of the blade surface, as well as for the blade passage's bottom wall, are introduced.
介绍了汽轮机动叶片叶身平均对流换热表面传热系数和叶片流道下壁面对流换热表面传热系数的计算方法和计算公式。
As a result, heat dissipating capacity, metal thermal intensity and free convection heat transfer coefficient of the longitudinal closed finned tube are higher than those of the open finned tube.
结果表明，封闭式纵向翅片管的散热量、金属热强度以及自然对流换热系数都要高于开放式翅片管。
Natural convection can affect the heat transfer coefficient in the presence of weak forced convection …
自然对流可能影响前面所述的弱强制对流热传递系数。
Try to make the cold, hot water flow passage of convection heat transfer coefficient is equal or close to, to get the best heat transfer effect.
尽量使冷、热水流道内的对流换热系数相等或接近，从而得到最佳的传热效果。
Try to make the cold, hot water flow passage of convection heat transfer coefficient is equal or close to, to get the best heat transfer effect.
尽量使冷、热水流道内的对流换热系数相等或接近，从而得到最佳的传热效果。
应用推荐