UNIT bearing: an automotive bearing used that is sold as an assembled set and is non-adjustable; characterized by a cone with no large rib.
组合轴承单元：是一个应用于汽车上，在销售前预组装、无需调整游隙以及内圈没有大挡边的轴承单元。
With analysis of structure of cone roller bearing inner ring forgings, corresponding improvement on original forging technology has been put forward.
分析圆锥滚子轴承内圈锻件结构，对原锻造工艺中的不足提出了相应的工艺改进措施。
STAND: Overall width of the assembled bearing; refers to the combination of sizes of the cone, outer diameter, cup, inner diameter, and roller.
座高：整套轴承的总宽度；参考内外圈尺寸，外径，内径以及滚子。
CAGE: Spacer used to maintain proper roller distribution around cone in assembled bearing; holds unit together.
保持架：轴承组件中用于使滚子保持一定间隔分布在内圈滚道上的装置。
Cup: one of four basic components of the assembled bearing. Also referred to as the outer race; the cone assembly fits into the cup.
外圈：轴承组件的四个基本组件之一，也称作外滚道；内圈装配在外圈里。
Since the gear reducer is working with load, attention shall be paid to the temperature increase of axial cone bearing and sliding thrust bearing oil sump.
因为减速机此时已经是带负荷运转，所以应特别注意输入轴锥轴承的温升和滑动推力轴承油池的温升有无异常现象等。
As to gear noise, the writer put forward first that, in order to solve the gear noise problem, the preload for the cone bearing must be settled first.
针对齿轮噪音，首次提出：要解决齿轮噪音问题，首先解决锥轴承预紧。
Compared the number of cone bit bearing capacity and concluded: diamond wheel bearing life is far greater than the cone drill bit bearings.
对比了牙轮钻头的轴承能力数，得出结论：轮式金刚石钻头轴承寿命远远大于牙轮钻头轴承。
Bearing inner ring (shaft circle) of the basic cylindrical hole or holes in the internal tapered cylinder or cone in the axis line access.
轴承内圈(轴圈)的基本圆柱孔或圆锥孔的内接圆柱体或内接圆锥体的轴心线。
Based on the Cone Index bearing capacity and shearing strength of paddy in Hunan Province, we designed the lug wheel for powered tiller in this province.
根据湖南省一般淹水水田和旱态水田的圆锥指数承压特性及土壤力学参数剪切特性来设计湖南独轮耕整机的驱动轮。
The governing equations of dynamic pressure distribution, i. e. dynamic cone Reynolds equations are derived. The calculating models of dynamic characteristics of cone plain bearing are given.
针对精密机床主轴系统中应用广泛的圆锥形滑动轴承，建立起了动态压力分布控制方程——圆锥动态雷诺方程，给出了动特性系数计算的数学模型。
The experimental results could be directly used in the sliding bearing design for cone rock bits.
这种研究结果可以直接应用于钻头滑动轴承的设计。
Calculate the engaging distance between inserts and slots and the least thickness from bearing to contour of cone automatically.
自动计算相邻牙轮之间牙齿与齿槽的最小啮合间隙和牙齿底部到牙轮内孔的最小壁厚。
The recent development trend of cone bits is to realize their high speed. Faster the speed of bit is, the more weak of common bearing seals worked under the rough environment is.
牙轮钻头目前的发展趋势是实现高速化，随着钻头转速的不断提高，在恶劣环境下工作的普通轴承密封这一环节的薄弱性将显得越来越突出。
A method of determining the load on journal bearing of three-cone bit is described in this paper.
本文阐述了三牙轮钻头滑动轴承载荷的测试方法。
Results of the experiment show that hydrostatic gas-lubricated bearing with self controlled cone slot restrictor possesses of very high static stiffness and satisfactory stability in certain range.
经试验，安装该节流器的推力轴承在一定载荷范围内静态刚度接近无穷大，而且无气膜不稳定现象发生。
This paper deals mainly with the formulation, processes and microstructure of the diffusion Vanadium-coating with powder on the journal bearing steel of cone bits.
本文着重研究了牙轮钻头轴承用钢的粉末渗钒配方、工艺和渗层的组织结构。
The main failure patterns of the sliding bearing of a cone bit are gluing and abrasion.
钻头滑动轴承的主要失效形式是胶合和磨粒磨损。
Therefore, the venerable cup-and-cone bearing arrangement is still the most effective.
因此，老杯和锥轴承的安排仍是最有效的。
If an oil slinger is used behind the inner pinion bearing cone, deduct the thickness of the slinger from the dial indicator reading and use that total for shim selection.
如果抛油环用在内侧驱动小齿轮内圈的后面，从针盘指示表读数中扣除抛油环的厚度，垫片的选择用这个总数。
If a similar seal existed for the axial cup-and-cone bearing, the longevity would exceed that of the cartridge bearing.
如果存在类似的密封轴承的轴向杯和锥，寿命将超过轴承的墨盒。
The failure mechanism of journal bearing of roller cone bit is analyzed, the failure type is adhesive wear, and main factors affecting the adhesive wear are analyzed.
分析了牙轮钻头滑动轴承失效的机理，论证了牙轮钻头滑动轴承失效形式主要为粘着磨损，分析了影响轴承粘着磨损失效的主要因素。
The solid of journal bearing pair is created with ANSYS. Some inserts are built and added to the cone solid. The pressure load is applied on the several insert surface, which is more practical.
利用ANSYS建立了牙轮钻头滑动轴承副实体，与前人所不同的是增加了牙齿实体，并在牙齿顶部加上了面载荷，因此数字模型更能反映实际情况；
The solid of journal bearing pair is created with ANSYS. Some inserts are built and added to the cone solid. The pressure load is applied on the several insert surface, which is more practical.
利用ANSYS建立了牙轮钻头滑动轴承副实体，与前人所不同的是增加了牙齿实体，并在牙齿顶部加上了面载荷，因此数字模型更能反映实际情况；
应用推荐