The contact stress distribution in the rabbet of the aircraft engine blade was determined by combining the experimental and numerical methods.
文中将实验检测技术与数值计算方法相结合，求解飞机发动机叶片榫头上的接触应力分布。
After calculating with finite element method and photoelastic-test, it shows that the contact stress distribution is not in keeping with the formulas given by some bearing hand books and textbooks.
通过有限元计算及光弹性实验，结果证明，滚针轴承的接触应力分布与轴承手册和教科书中所给出的公式不符。
Aimed at a straddle blade root, the influence of the interface friction coefficient and initial clearance on the contact force distribution, load distribution and the maximum stress is analyzed.
文中以一菌型叶根为对象，分析了界面摩擦系数和初始间隙对接触力分布、载荷分配及最大应力的影响。
The distribution of the contact stress of FG is obtained in the different meshing locations during the meshing.
获得了在啮合过程中不同的啮合位置面齿轮的接触应力的分布规律。
Particle penetrating direction has influences on the magnitude of surface deformation, contact pressure and stress, and the distribution forms of contact pressure and stress.
磨粒侵入方向不仅影响材料表面变形、表面接触压力和表层应力的大小，而且会引起压力和应力分布形状的改变。
The stress distribution in the Hertz's elastic contact between two spheres is reviewed briefly.
本文简要回顾了两球面之间赫兹弹性接触的应力分布。
The tooth deformation includes the contact deformation, deflection, base deformation and the influence of the body deformation, and the contact stress and the stress distribution are computed too.
轮齿变形包括轮齿接触、挠曲、基础变形和齿轮本体变形的对它影响，还有接触应力和分布。
The elastic contact problem is analyzed in finite element method (FEM) and is used to the parameters' distribution and contact stress of the joint are obtained on the base of ANSYS code.
基于ANSYS软件平台求解弹性接触问题，获得了榫联接结构接触应力及接触状态量的分布；
Then carry on the contact analysis to roll pair, study the stress distribution situation between the roll pair.
然后再对轧辊副进行接触分析，研究轧辊副的接触应力分布情况。
The analysis on fatigue cracks of the outer race of aero-bearing shows that the distribution of residual tensile stress on race surface could reduce its contact fatigue life.
航空轴承外圈的疲劳裂纹分析表明，套圈表面的残余压应力分布致使轴承表面接触疲劳寿命降低。
The results showed that the major cause of thread gluing is over plastic deformation of partial thread face, and that the distribution of contact stress can be improved with the taper mutation, wh...
认为产生粘扣的主要原因是螺纹齿面局部过量的塑性变形，通过变锥度的方式能使接触应力分布规律得到改善，并在现场生产中得到验证。
Objective To determine the characteristics of the normal radiocarpal contact and the relationship between the stress distribution and wrist position.
目的明确正常腕关节桡腕关节面的应力分布特点及其与腕关节位置的关系。
Via analysis of different plate thickness combinations of equality height spacer plate group, contact stress curves and contact area distribution among the plates were got.
对整体高度恒定的垫板组的不同板厚组合进行分析，得到了不同组合时各层垫板间的接触应力曲线，并统计了各个接触层间的接触面积。
The distribution of pre-stress in the multi-layer structure is related to the global and local rigidity, the contact area and the clearance of superimposition.
结构内部的预紧力的大小和分布与结构的整体刚度、结合部位的局部刚度、过盈配合间隙、接触面积等因素有关。
The distribution of pre-stress in the multi-layer structure is related to the global and local rigidity, the contact area and the clearance of superimposition.
结构内部的预紧力的大小和分布与结构的整体刚度、结合部位的局部刚度、过盈配合间隙、接触面积等因素有关。
应用推荐