Finally, I tested the parsing by checking to see if the object contained a cooling rate multiplier.
最后，通过检查此对象是否包含冷却率乘数测试解析过程。
For maximum softness and ductility the cooling rate should be very slow, such as allowing the parts to cool down with the furnace.
为了得到最大柔软性和延展性冷却速率应该很慢，比如让零件与炉子一起冷下来。
The results show that, increasing cooling rate, pre-deformation and grain refinement are useful for spreading of the non-equilibrium microstructure around the primary grains.
结果表明：增加冷却速率、预变形处理和晶粒细化有利于初始凝固组织中存在的非平衡组织的分散细化。
Simulating different solidification cooling rate with step-metal mould and sand mould, the effect of solidification cooling rate on microstructure and properties of high boron steel were studied.
利用阶梯型腔金属模和砂型模拟不同的冷却速度，研究了冷却速度对高硼钢凝固组织和性能的影响。
The RTP temperature, the RTP time, the cooling rate, the ambient and the dopant atoms influenced the density and distribution of point defects in wafers, and then affected oxygen precipitates.
快速热处理温度、时间、降温速度、退火气氛、掺杂原子等都对硅片中点缺陷的形成及分布产生影响，进而影响氧沉淀的形成。
The maximum thickness of amorphous alloy ribbons can also be determined by this formula and the critical cooling rate.
由这个公式和临界冷却速度还能决定出非晶态合金丝带的最大厚度。
Results show that with the increase of cooling rate or decrease of measurement temperature, both the yield stress and yield time increase, but the yield strain decreases.
发现在相同测量方式下，随降温速率的增大或测量温度的降低，屈服应力增大、屈服时间变长、屈服应变减小。
The glass transition temperature of PLLA decreased with the increase of cooling rate.
玻璃化温度和结晶度随着降温速率的降低而增大。
In order to avoid the possible softening of HAZ in welding of RPC steel, laser welding is one of the best methods due to its faster heating and cooling rate and narrower HAZ.
激光焊接有很快的加热和冷却速度，热作用范围窄，在合适的工艺条件下可避免RPC钢HAZ的软化，激光焊接是高质量焊接RPC钢的方法之一。
The results indicate membrane permeability and cooling rate are main factors that affect the cell shrinkage.
计算结果表明，膜的渗透性和冷却速率是影响细胞体积收缩的主要因素。
The major reason of the formation of quench cracks is the contamination of oxygen in the early processing or unsuitable quench cooling rate during heat treatment.
基于两种机制的提出，可以较好地说明影响淬火裂纹形成的主要原因是氧的污染和不适宜的淬火冷却速度。
The influences of different microstructure, silicon content, quenching temperature and cooling rate of the SiCr white cast iron on its abrasive wear performance were investigated.
研究了硅铬白口铸铁不同组织、不同含硅量、不同淬火加热温度及冷却速度对其耐磨粒磨损性能的影响。
The transformed ferrite volume fraction increases and grain size decreases with the increase of cooling rate.
随着冷却速率的增加，铁素体体积分数减少，晶粒尺寸变细。
The transformation rule of diameter of droplets between cooling rate and undercooling can be analyzed in drop tube.
对落管中冷却速率和过冷度随液滴直径的变化规律进行了分析。
The solidification modes of liquid phase of semi-solid AZ91D Mg alloy were in close relationship with the degree of supercooling determined by cooling rate.
AZ 91d镁合金半固态液相的凝固方式与冷却速度所决定的过冷度有重要关西安理工大学硕士学位论文系。
Steel grain-reinforced pure copper cast composite was gotten successfully by suspension casting process and controlling the cooling rate.
采用悬浮浇铸工艺并控制冷却速度成功地得到了钢颗粒增强纯铜基铸造复合材料。
However, the cooling rate obtained in these tests was very difficult to do under the industrial scale.
然而，实验室条件下试验所达到的冷却速率在工业化生产中较难实现。
The methods to improve the intensity of cold-rolled sheets is to add some useful alloying elements during steel-making and improve the cooling rate annealing treatment.
提高冷轧薄板机械强度的方法主要是在炼钢时添加有益的合金元素及在热处理时提高退火后的冷却速率。
The as-cast bainite steel studied in this paper could obtain bainite directly in the as-cast condition through alloying and controlling the cast cooling rate without heat treatment.
所研究的铸态贝氏体钢是通过合金化和控制冷却速度的方法在铸态下直接得到贝氏体组织的，不需热处理即可获得所需的组织和性能。
The influences of cooling rate after the forge on the heating temperature and time of apheroidized annealing of steel T10 was studied.
研究了锻造后的冷却速度对T10钢等用球化退火加热温度和保温时间的影响。
The quantitative relationship between secondary dendrite arm spacing and solidification cooling rate of AZ91 was obtained by regressive analysis.
用数学回归的方法得到了AZ91镁合金的凝固冷却速度与二次枝晶间距的定量关系式。
The cooling rate is faster in chromite sand mold, but also causes more porosity in castings.
铬砂制作的砂模可让铸件有较快的冷却速率，但也产生较多的微孔隙。
The more the increase of cooling rate or pre-deformation, the more the secondary dendrite arms are easy to coarsen.
冷却速率越大或预变形处理以后的试样在熔化过程中更容易发生二次枝晶臂之间的合并。
The Raman spectroscopy measurements indicate that silicate glass structure is insensitive to cooling rate.
拉曼光谱检测显示，硅酸盐玻璃的结构对降温速度变化不敏感。
The critical cooling rate for the glass formation in the tube was determined.
确定了在落管中形成玻璃的临界冷却速率。
Parameters effecting on dry fractionation of lard are crystallization temperature, cooling rate, crystal growing time, agitation rate, separating manner.
影响猪油干法分提参数有：结晶温度、冷却速率、养晶时间、搅拌速率及分离方式。
The effect of cooling rate and undercooling temperature on the rate and amount of dehydrogenation was studied by magnetic balance simulation method.
用磁秤模拟方法研究了冷却速度和过冷温度对镍铬钢排氢速度和排氢量的影响。
The effects of opening flask temperature and cooling rate on low and high temperature age-hardening alloy casting are tested and studied.
试验研究了开箱温度和冷却速度对低、高温时效型合金时效硬化效果的影响。
It includes the effect of manganese content, solution treatment temperature and cooling rate on the non equilibrium segregation of manganese and condition of segregation formation.
研究了锰的质量分数、固溶处理温度和淬火冷却速度对锰不平衡偏聚的影响和不形成锰偏聚的条件。
It includes the effect of manganese content, solution treatment temperature and cooling rate on the non equilibrium segregation of manganese and condition of segregation formation.
研究了锰的质量分数、固溶处理温度和淬火冷却速度对锰不平衡偏聚的影响和不形成锰偏聚的条件。
应用推荐