Cylindricity error is defined as the changes between measured column and ideal column.
圆柱度误差是指实际被测圆柱面对其理想圆柱的变动量。
The verticality of vertical milling machine spindle and the worktable can affect hole cylindricity.
立式铣床主轴与工作台面的垂直度会影响孔的圆柱度。
The experimental results show that the roundness is improved by 40% and cylindricity by 23% after compensation.
实验结果表明，补偿后的工件圆度误差平均改善了40%，圆柱度误差平均改善了23%。
The cylindricity error separation and reconstruction method proposed in this paper was systematically verified.
利用自律验证法对本文提出的圆柱度误差分离及重构方法系统地进行了实验验证。
Because of the limit of measuring tools, the traditional methods can not evaluate the cylindricity error of internal pipe.
由于测量工具的限制，传统方法对无法充分接触的内部管道的圆柱度难以测量。
Based on industrial CT, this dissertation studied the cylindricity error evaluation and inner surface display of pipeline.
本文以工业CT为基础，研究了工件内部管道的圆柱度测量与内表面显示算法。
The experimental results show that the cylindricity error can be evaluated effectually and accurately using this algorithm.
试验结果表明，该算法可以有效、正确地评定圆柱度误差。
It can be used for measuring dynamic balance and spindle rotating accuracy of machine tools, and cylindricity of workpieces.
它可测量机床的动平衡，也可测量机床主轴的回转精度、工件圆度等。
Cylindricity - describes a condition of a surface of revolution in which all points of a surface are equidistant from a common axis.
圆柱度-描述了一个条件的旋转面，使所有的点面距离相等，一个共同的旋转轴。
The cylindricity error can be got by optimization. The results show that this method can get cylindricity error without damage and touch.
实验结果表明，该方法可以在无接触无破坏的前提下得到较为准确的测量结果。
While the plane is measured by using the cylindricity measuring instrument and square, the data acquisition should be done at the same time.
首先利用圆柱度仪和角尺对被测件进行测量，同时采集原始测量数据，然后利用最小二乘法实现平面度误差的评定。
The honed cross hatch in cylinder bore of engine and the cylindricity of cylinder bore shall affect directly the operating mode and life of engine.
发动机缸孔平台网纹珩磨得是否合理和缸孔圆柱度的优劣直接影响到发动机的工况和寿命。
The in-process measurement principle for the spindle rotation error is presented and the roundness and cylindricity on-line measurement and compensatory control system is developed.
提出了实时测量机床主轴回转误差的原理和方法，建立了工件圆度及圆柱度在线测量及补偿控制系统。
There are many kinds of pipelines in real workpiece. The cylindricity error evaluation and inner surface display of pipe are significant for evaluating performance and service life.
工件中常包含各种各样的管道，对管道的圆柱度误差测量和内表面显示对评定工件的整体性能和使用寿命有着重要意义。
This paper models the least square algorithm of the cylindricity error in the rectangular coordinates, whose center may be set on random and all discrete data can be sampled optionally.
建立了采样数据为直角坐标值、坐标原点可以任意选取、各离散采样点之间也不要求为等角度间隔情况下，圆柱度误差评定的最小二乘数学模型。
This paper presents a method to evaluate cylindricity errors. It USES best uniform approximation to process the sample data measured continually and dynamically along a cylindrical spiral.
本文提出沿圆柱表面的螺旋线对圆柱度作动态测量，并应用最佳一致逼近方法对其展开的测量数据来评定圆柱度误差值。
In order to measure the cylindricity error of the pipe which is in the internal part of a workpiece, this paper studies a cylindricity error evaluation method based on industrial CT images.
针对工件内部管道圆柱度误差测量的问题，研究了一种基于工业CT图像的圆柱度误差测量方法。
The precision of the support bearing of the horizontal milling machine bracket affects the rotation precision of the cutter rod, thus affecting the dimension precision and cylindricity of the hole.
卧式铣床支架的支承轴承的精度会影响刀杆的回转精度，从而影响孔的尺寸精度和圆柱度。
Several evaluation models of cylinder's taper are built based on the data measured on cylindricity measuring instrument using a double-section measuring method and a multi-section measuring method.
利用在圆柱度仪上采用两截面和多截面测量法测得的数据，建立适用于圆柱体锥度评定的几种模型，并建立了圆柱体端面和径向跳动在圆柱度仪上测量与评定的模型。
This paper introduces an outer diameter detector, using two inductance sensors. It can automatically display the outer diameter, average diameter and cylindricity of all kinds of shafts and sleeves.
本文研制的高精度电感式外径检测仪采用二个电感传感器，能自动显示各种轴套的外径、平均直径和圆柱度。
This paper introduces an outer diameter detector, using two inductance sensors. It can automatically display the outer diameter, average diameter and cylindricity of all kinds of shafts and sleeves.
本文研制的高精度电感式外径检测仪采用二个电感传感器，能自动显示各种轴套的外径、平均直径和圆柱度。
应用推荐