The last layer is to be applied uniformly, with no surface defects.
最后一层涂层应涂刷均匀一致没有任何表面缺陷。
One of the most prevalent defects of hard drives is bad sectors on the disk surface.
其中一个最普遍的缺陷，硬盘驱动器是坏扇区对硬盘的表面。
This article analyzes the main factors and selection of rational cutting conditions influencing the surface flatness error and other defects in sawing marble plates with diamond saw blade.
本文分析了金刚石框锯在锯切大理石时，引起表面平面度偏差和其它缺陷的主要因素以及合理工作条件的选择。
The shunt resistance represents the loss due to surface leakage along the edge of the cell or due to crystal defects.
分流电阻表示由于沿电池边缘的表面漏流或晶格缺陷造成的损耗。
Minor cracks holes and surface defects shall be made good with exterior grade water-mixed filler or masonry cement before application of the primer or first coat of paint.
在第一次应用或涂底漆之前，较小的裂缝、孔及表面缺陷应采用浆、水混合填料或水泥浆和砌浆进行填塞及填充。
This paper describes the methods of controlling the frame quality in terms of process design, mould design, control of deformation and defects from welding surface treatment, etc.
从工艺设计、胎具设计、控制焊接变形和缺陷、表面处理等各环节实行严格的品质控制，多年来生产出多种型号的车架全部为合格品。
Pinhole free film. A surface free from any defects.
无针孔的涂膜，没有表面缺陷的表面。
The main surface of the workpiece, the assembly surface should be first processing, thus early detection of defects in the workpiece surface may be the main.
工件的主要表面，装配基面应先加工，从而及早发现毛坯中主要表面可能存的缺陷。
Defects detection for texture surface is one of the important research problems in machine vision, and can be widely used in surface quality control of different products.
纹理表面的瑕疵检测是机器视觉的一个重要研究课题，已经广泛用于各种产品表面质量控制。
PITTED: Small indentations appearing as black dots on finished surfaces of any piece of product; undesirable surface defects.
麻面：在任何成品零件的表面上出现的小的黑色的麻点，这是不希望的缺陷。
Coating surface should be no leakage, dew iron and other defects.
镀件表面应无漏镀、露铁等缺陷。
Usually, if explosive particles have less crystal defects, more smooth surface, and higher crystal density, the explosives have lower sensitivities and better safety.
通常讲，具有更少的晶体缺陷，更光滑的外形、更高的晶体密度，则有利于降低炸药的感度，提高安全性。
Statistic data shows that 65% of bearing invalidation formats is induced by surface defects of steel balls.
实验统计表明：在轴承的失效形式中，由于钢球表面的缺陷而引起的裂纹、裂缝造成的轴承失效达65%。
Surface defects in ceramic bearing balls may significantly affect ball strength and reduce rolling contact fatigue lifetime.
陶瓷轴承球的表面缺陷会严重降低球的强度和滚动接触疲劳寿命。
All kinds of defects appear in the surface of components which under the repeated impact load, and the surface defects make the earlier damage and failure.
在多冲这种动载应力波作用下的零部件大都在多冲的接触表面出现或引发各种缺陷并导致早期损伤失效。
The purpose of weld guide bending test is to detect plasticity of welding joint, welding process and surface defects of materials.
焊缝导向弯曲试验的目的是检查焊接接头的完好性和塑性以及材料的焊接工艺和表面缺陷。
Huanghua pear is an important fruit in China. The fruit diameter and surface defects are important indices in the classification of Huanghua pear.
黄花梨是中国的一种重要水果，果径和果面缺陷面积是黄花梨分级的两项关键指标。
To increase nucleation density, the methods of introducing defects on substrate surface are more effective in the diamond thin films growth by means of the low pressure vapor phase deposition.
在低压气相生长金刚石薄膜过程中，通过在衬底表面引入缺陷，通常是一种行之有效的提高成核密度的方法。
Some defects exist in the Surface dense layer.
表面致密层存在有缺陷。
Cracks leading to spalling were initiated at surface defects and boundaries between nitriding layes and the core.
导致剥落的疲劳裂纹开始于表面缺陷和氮化层与心部交界处。
A surface inspection system for cold rolled strips is introduced, which is used in on-line detection and recognition of surface defects on cold rolled strips.
介绍一套目前正在开发的冷轧带钢表面质量在线监测系统，该系统用于在线检测和识别冷轧带钢的表面缺陷。
Defects due to an unsatisfactory rate of teeming. This kind defects include splashing, rippled surface, and laps or folds.
由于浇注速度掌握不好而引起的缺陷。这种缺陷包括飞溅、波皱面以及重皮或折叠。
The surface defects of silver COINS was analysed with auger electron spectroscopy (AES), Scanning electronic microscope (SEM) and energy dispersive spectrum (EDS).
采用扫描电镜、能量色散谱和俄歇电子能谱检测方法，对银币表面缺陷进行了分析。
This paper introduced the characters of surface defects of hot strips and data mining thesis briefly at first.
本文首先对热轧带钢表面质量缺陷发生的特点及数据挖掘理论进行了简单介绍。
The grade identification technology of surface defects of green orange based on computer vision was studied.
应用计算机视觉研究了绿橙表面缺陷的分级检测技术。
This new method can accurately, timely and effectively check out various defects over the strip surface.
该方法速度快，精度高，实时性好，可有效地检测到带钢表面的各种缺陷。
The reason and prevention of four kinds defects including surface wrinkled skin (carbon built-up), chock, blow hole, deformation, was introduced in this part of the article.
本部分主要介绍表面皱皮（积碳）、呛火、气孔、尺寸超差及变形等缺陷的产生原因和防止方法。
The reason and prevention of four kinds defects including surface wrinkled skin (carbon built-up), chock, blow hole, deformation, was introduced in this part of the article.
本部分主要介绍表面皱皮（积碳）、呛火、气孔、尺寸超差及变形等缺陷的产生原因和防止方法。
应用推荐