• Effect of strain rates on peak flow stress is relate to deformation temperature.

    应变速率峰值应力影响变形温度有关

    youdao

  • It is found that flow stress is dependent on deformation temperature and strain rates.

    结果表明流变应力取决于变形温度变形速率

    youdao

  • The strain rate sensitivity exponent increases little with increasing deformation temperature.

    随着变形温度提高合金的应变速率敏感指数值变化很小

    youdao

  • Thermal deformation temperature and liner expansion coefficient of the composite were decreased.

    复合材料变形温度有所降低,但线膨胀系数减小。

    youdao

  • When deformation temperature is constant, flow stress increases with the increase of strain rate.

    温度一定时,流变应力随着应变速率升高而增大

    youdao

  • Increasing deformation temperature, enhancing strain and increasing strain rate can accelerate transformation.

    变形温度升高、变形量变形速率增加相变有促进作用。

    youdao

  • Dynamic recovery and recrystallization of the composite generate with the increasing of deformation temperature.

    变形温度升高,复合材料发生动态回复结晶。

    youdao

  • The results show that the softening ratio increases with the increase of deformation temperature and interval time.

    结果表明静态软化变形温度升高道次间隔时间延长而不断增加。

    youdao

  • Deformation temperature and pass strain are the key factors controlling the cracking of the samples during deformation.

    变形温度应变量精确控制保证合金形变中不发生开裂关键

    youdao

  • The resin toughness, the casting of the thermal deformation temperature is a good Comprehensive Performance winding resin.

    树脂韧性好,浇铸变形温度一种综合性能良好缠绕用树脂。

    youdao

  • The resin toughness, the casting of the thermal deformation temperature is a good comprehensive performance winding resin.

    树脂韧性一种综合性能良好缠绕用树脂。

    youdao

  • The evolution law of microstructure and properties of 7a04 alloy at different deformation temperature and times was studied.

    研究不同变形温度变形次数7a04铝合金组织性能变化规律

    youdao

  • The inner maximum resistance force and the maximum stress of the specimen decreases as the deformation temperature increasing.

    形变速率相同条件下,随变形温度升高,试样内部最大形变抗力最大应力呈下降趋势

    youdao

  • The results show that the flow stress and peak strain increase with increasing strain rate or decreasing deformation temperature.

    结果表明:实验条件下,流变应力峰值应变变形温度降低应变速率提高而增大

    youdao

  • The dynamically recrystallized grain size increases with increasing deformation temperature and reduces with increasing strain rate.

    动态再结晶晶粒尺寸随着变形温度升高而增大,随着应变速率升高减小

    youdao

  • The results showed that the flow stress and deformed microstructure were greatly affected by strain rate and deformation temperature.

    结果表明应变速率变形温度合金流变应力变形组织显著影响

    youdao

  • The results show that the flow stress and peak strain increase with either increasing strain rate or decreasing deformation temperature.

    试验结果表明流变应力峰值应变变形温度的降低和应变速率的提高而增大

    youdao

  • The results show that the model of deformation resisitance is different at the same deformation temperature and the different stain rate.

    结果表明同一温度下,应变速率不同,材料流变应力模式不同;

    youdao

  • Based on the resin curing the hardness and thermal deformation temperature higher, but also has a good climate of tolerance and toughness.

    基础树脂固化后硬度变形温度较高同时具有良好韧性和耐气候

    youdao

  • Effects of SS400 steel's deformation temperature and strain rates on its deformation behavior was studied using single pass compressing test.

    采用道次压缩试验研究变形温度变形速率SS400热变形行为影响

    youdao

  • The deformation temperature is the main factor which affects the grain size of austenite or ferrite when the strain rate is not changed largely.

    说明变形速率不太高情况,变形温度影响氏体铁素体晶粒尺寸主要因素

    youdao

  • Deformation, deformation temperature, deformation velocity and breaks after deformation have important influence on recrystallization grains grown.

    变形量,变形温度,变形速度,变形间歇时间等因素再结晶晶粒长大重要影响

    youdao

  • The size of dynamically recrystallized grain decreased with the increase of strain rate and increased with the increase of deformation temperature.

    动态再结晶晶粒尺寸应变速率增加减小,随变形温度增大增大。

    youdao

  • The experimental results show that the deformation temperature has significant influence on peak flow stress of the semi-solid LY11 alloy and as-received.

    试验结果可知:变形温度LY 11合金峰值应力影响显著,对稳态应力影响较小。

    youdao

  • With the increase of deformation temperature, thick second phase reduces, the strength of T6 alloy increases, but plastic decreases first and then increases.

    变形温度升高,合金中的粗大第二减少T6态铝合金强度变形温度升高增大塑性降低后增加。

    youdao

  • The resin produced by the flame-retardant products with high strength and mechanical properties, thermal deformation temperature, curing speed, and good soak.

    树脂所生产制品具有很高阻燃性能机械强度变形温度高,固化速度快,浸透性

    youdao

  • The effect of deformation temperature and deformation speed on the limit drawing ratio (LDR) and microstructure of the roll-casting AZ31 magnesium alloy sheet.

    研究变形温度、变形速度铸轧az31镁合金极限拉深(ldr)组织影响。

    youdao

  • The DMA analysis indicated that radiation crosslinking raised heat deformation temperature of PCL and caused a rubbery state after the melting of PCL crystals.

    DMA分析表明,聚内酯辐照交联弹性模量耐热性能显著提高

    youdao

  • The effect of organic rectorite on the viscosity, gel-time, heat deformation temperature, mechanical properties and wet-heat resistant property were researched.

    分别研究有机粘土树脂体系粘度凝胶特性、力学性能变形温度湿热性能影响

    youdao

  • Impact rupture suface of the composites was observed by scanning electron microscope, and the load deformation temperature and mechanical properties were tested.

    通过扫描电镜观测复合材料冲击断面形貌,测试了复合材料的负荷变形温度力学性能

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定