The analysis and design of computer control system for a new type of fruit automatic process equipment is introduced.
介绍了一种新型的集装箱式果品绿色自动化加工设备中计算机控制系统的分析与设计。
The paper introduces the hard ware composition and soft ware design of computer control system of spark frequency of high pressure static dust extractor.
本文介绍了高压静电收尘器火花频度计算机控制系统的硬件组成和软件设计。
This paper presents hardwares design and realization of computer control system of three degree - of - freedom motion platform.
本文介绍了协同式三自由度运动平台计算机控制系统的硬件设计及实现方法。
The design and implementation of reheating furnace computer control system based on the dynamic mathematical model and the heuristic optimization strategy is discussed in this paper.
本文阐述了一个基于动态数学模型及启发式优化策略的连续加热炉计算机控制系统的设计与实施。
The design of programming part related to the mode of intelligent control system can realize the precision control to multi-points temperature by simulation analysis in computer.
第二部分软件设计，按智能控制系统的模式，实现计算机对多区温度的精确控制。
For simulation of winding tension control system using computer, the parameters about system design and the system performance with these parameters can be quickly obtained.
采用计算机对卷取张力控制系统仿真，可以快速获取系统设计参数和这一参数时的系统性能，使现场调试变得方便快捷。
A design scheme of motion control system based on parallel port of computer was proposed.
提出了一种基于计算机并行口的运动控制系统的设计方案。
This paper describes the design method of Single Board Computer Control System for a High precision servo table.
本文叙述了高精度伺服转台的单板计算机控制系统的设计方法。
Introduced the system software and hardware design, function, control principle and operation of computer full automatic control system of steam lumber kilns.
介绍了蒸汽式木材干燥窑计算机全自动控制系统的软、硬件设计、系统功能、控制原理及系统使用方法。
MATLAB is a software package used in science and engineering calculation. It is convenient of MATLAB to carry out computer aided design of control system.
MATLAB是一种面向科学与工程计算的高级语言，应用MATLAB进行控制系统的计算机辅助设计快捷方便。
The configuration of the computer system, system hardware and software design are presented. Also, the control results of the system are introduced in detail.
介绍了计算机系统配置、系统硬件配置及软件设计，还详细介绍了系统控制效果。
In order to resolve the problems of energy saving and safe operation of boiler water treatment device, applies computer supervisory control and data acquisition system on engineering design.
为了解决锅炉水处理装置节能和安全运行问题，在工程设计中采用了计算机监控和数据采集系统。
At last the main introduction is the using of LCD in combination with 80c196kc in single chip computer control system, including hardware interface and software design.
最后，主要介绍了液晶显示器在单片机控制系统中与80c 196kc的结合使用，其中包括硬件接口以及软件设计。
Design and application of two level computer control system that consists of PLC and process computer for concentrate measuring and sampling in copper melting plant are described.
介绍在铜冶炼厂由PLC和上位机组成的两级精矿自动计量和取样计算机控制系统的设计和应用情况。
Finally, some proposals on research and design of communication network for process computer automatic control system are offered.
最后，对计算机过程控制系统的通讯网络试制研究提出些建议。
This article briefly introduces the process of production input control for modifying design of buses and presents how to design database of production input control by the computer system.
简要介绍客车设计更改后的生产投入控制应用流程及怎样用计算机系统建立生产投入控制数据库。
A design and application of industrial control PC computer in control system for an automation green house is introduced.
论述了采用工业PC计算机实现自动化温室控制系统的设计与应用。
In addition, the hardware designing and the software programming, also the computer realization method, is studied, so the whole complex design process of the computer control system is studied.
另外研究了控制系统的硬件设计和软件编程及采用计算机控制的具体实现方法，较全面说明了复杂计算机控制系统的设计过程。
Aiming at the automobile safety-detection, the paper discusses the structure and design of the computer intelligent detection and control system.
针对汽车安全检测，本文论述了其计算机智能测控系统的组成和设计要点。
The hardware design for computer control system in synthetic fiber industry and the network composition and function of the computer control system were introduced.
介绍合纤工业中计算机控制系统的硬件设计，以及该系统的网络构成和功能。
This paper presents the design and actual circuit of a computer control system for the North-Seeker with ARM7 (here LPC2292 is used) as core microprocessor and the flexible gyro as sensor.
介绍了一种以arm7单片机(选用LPC 2292)作为核心处理器，以挠性陀螺为传感器的寻北仪方位角-数字转换系统设计及实现电路。
This paper introduces the basic automatic sticky box machines, and technology and processes through research design a set of sticky box based on PLC machine computer control system.
本文介绍了全自动粘箱机的基本工艺和流程，并通过研究设计一套基于PLC控制的粘箱机控制系统。
Finally the structural design and the implemented scheme of a computer control system for an industrial spiramycin fermentation process is described in detail for illustration.
最后，针对螺旋霉素工业发酵过程计算机控制系统的实际课题，运用上述方法对其系统结构设计和实施方案作了详细介绍。
This article mainly introduces a design method of the lower computer of a hotel guest room control management system based on AT89C55, which is cheap and reliable and have more complete functions.
本文着力介绍了一种基于AT 89c55的价廉且功能相对完备、运行稳定可靠的酒店客房控制管理系统的下位机的设计方法。
The design of a CAN based computer control temperature system is introduced.
并设计一基于CAN总线的计算机温度控制系统。
The mechanical design, sensors system design, DC Servo control system design and data acquisition system design of the man-computer stiffness display interface device are introduced.
介绍了该人机触觉再现接口装置的机械设计、传感器系统、直流伺服控制系统以及数据采集系统的设计。
In this paper, design and realization of the fault-locating system for LLP10B fire control computer is introduced. It gives the system structure and working proceeding.
研究了LLP10B火控计算机故障分析仪的设计及实现；给出了该分析仪的系统组成和工作流程。
Principle, circuit design, hardware structure, software flow and features of dual computer switching circuit of FTK-3 hump automatic control system are introduced in this paper.
本文介绍了FTK-3型驼峰自动控制系统双机切换电路的原理、电路设计、硬件结构、软件流程和特点。
The last but not the least, the electrical wiring of vector inverter control cabin and design of computer control and data acquisition system are introduced.
最后简单介绍了本课题矢量控制变频控制柜的外部附件电气接线、计算机控制及数据采集系统的硬件设计等内容。
Introduces a device control system design based on micro -computer parallel port, gives the concrete design method of system hardware and software according to system requirement.
介绍了基于微机并口的某设备控制系统，并根据系统要求，详细讨论了系统的硬件和软件设计方案。
应用推荐