Three types of clutch are the coil-pressure-spring type, diaphragm-spring type, and semi centrifugal type.
离合器的三种类型为：螺旋弹簧式，膜片弹簧式和半离心式。
Diaphragm spring pressure plate assemblies are widely used in most modern cars.
膜片弹簧压盘组件广泛应用于在现代车辆上。
Mainly by the pilot valve seat, valve, diaphragm, spring, adjusting springs and other parts.
导阀主要由阀座、阀瓣、膜片、弹簧、调节弹簧等零件组成。
The center portion of the diaphragm spring is slit into numerous fingers that act as release levers .
膜片弹簧中间的部分撕裂成若干个指针大小般的片，充当回力（释力）杠杆。
Inside the pump, a flexible diaphragm connects to the rocker arm though a diaphragm spring, pull rod and link.
油泵中可变形膜片的泵膜通过膜片回位弹簧和膜片拉杆与摇臂相连。
Spring opposed , air operated diaphragm or piston, actuators are preferred for on-off applications.
弹簧平衡型、气动膜片或活塞，执行机构对于开关阀是首选的。
The diaphragm spring is a single thin sheet of metal which yields when pressure is applied to it.
膜片弹簧是一张薄金属片，当压力施加到膜片弹簧上，会产生变形。
Diaphragm (8) may be ruptured. Remove spring chamber (4) to inspect.
隔膜(8)可能会断裂。拆卸弹簧隔膜(4)进行检查。
Abstract: This essay is based on the typical auman CTX-1 BJ1049V9JEA vehicle technical parameters and designs the diaphragm spring clutch for it.
摘要：本设计是以典型欧曼ctx - 1系BJ 1049v9jea汽车技术参数为依据，对其进行膜片弹簧离合器设计。
When the clutch pedal is pressed, a cable or hydraulic piston pushes on the release fork, which presses the throw-out bearing against the middle of the diaphragm spring.
当离合器踏板按下时，电缆或者液压活塞将推动离合器分离叉杆，离合器分离叉杆推着外伸的轴承贴在膜片弹簧的中间。
Remove the relief valve cover, stem/diaphragm assembly, and relief valve spring.
拆卸安全阀阀盖，阀杆/隔膜总成，和安全阀弹簧。
Place the spring on to the diaphragm assembly.
将弹簧放置在隔膜总成上。
The two primary types of pressure plate assemblies are coil spring assembly and diaphragm spring .
有两个基本类型的压盘是螺旋弹簧组压盘和膜片弹簧压盘。
The causes for the elastic force attenuation of diaphragm spring are analyzed based on the stress distribution of loaded diaphragm spring.
本文从膜片弹簧受力变形后内部应力分布着手，分析了膜片弹簧早期弹力衰减的原因。
The tests of complete forklift truck shows that using diaphragm spring clutch in forklift truck is better than spiral spring clutch.
叉车整车试验表明在叉车上应用膜片弹簧离合器优于螺旋弹簧离合器。
According to the rules of the stress distribution, the maximum deformation of diaphragm spring and the minimum number of forced compression needed are proposed.
根据膜片弹簧工作过程中应力分布及变化规律，得到了强压时膜片弹簧变形量数值和强压所需次数。
Remove the piston and spring from the relief valve housing and thoroughly clean all parts including the diaphragm.
从安全阀外壳上拆卸活塞和弹簧，彻底清洗包括隔膜的所有部件。
Described the clutch diaphragm spring clutch, hydraulic remote operation, pneumatic servo booster.
膜片弹簧离合器，液压远距离操作，带气压伺服助力器。
Abstract: Inthis article, experimental research, theoretical calculation and finite element method have been used to analyze the load deformation characteristics of diaphragm spring.
摘要：本文通过实验研究、理论计算和有限元方法对膜片弹簧载荷变形进行了研究。
Single dry plate, diaphragm spring type, hydraulically operate.
单干板，膜片弹簧式，液压操作。
The pressure or differential pressure to be monitored ACTS on a diaphragm, which in turn ACTS against a spring.
压力或差压进行监测上的隔膜，在行为对一个春天来的行为。
Owing to a lot of merits, diaphragm spring clutches are widely used already in automobiles abroad instead of conventional coil spring ones.
膜片弹簧离合器具有许多优点，因此在国外汽车中已广泛应用并逐渐取代了传统的螺旋弹簧离合器。
The calculation models of the effective area, the rate of change of the effective area and the rate of change of the effective volume are established for the diaphragm air spring.
在膜式空气弹簧结构与计算模型的基础上，建立起膜式空气弹簧有效面积、有效面积的变化率及有效体积变化率的计算模型。
Three types of backpressure valves are diaphragm, spring and weighted lever.
有三种类型的回压阀，即隔膜式、弹簧式和负荷杆式。
The flexible diaphragm is connected to a plat cantilever - calibrated spring.
柔韧的膜片一扁平的悬臂校正弹簧相连。
Compared with the prior art, the simulation system for the diaphragm spring of the clutch can simulate load resistance of different types of diaphragm springs of clutches.
相比于现有技术，本发明所提供的离合器膜片弹簧的仿真系统可以实现对不同类型的离合器膜片弹簧的负载阻力进行仿真。
A finite element model for diaphragm air spring is created, and its dynamic characteristics are simulated and verified by test, with both results coinciding each other.
建立膜式空气弹簧的有限元模型，对其动态特性进行仿真和试验验证，仿真结果和试验结果吻合良好。
It is very important to guarantee support ring's welding quality for guarantee of Diaphragm Spring clutch's service life.
支撑环的焊接质量是保证膜片弹簧离合器使用寿命的一个重要因素。
Integrating the characteristic of diaphragm air spring, the air spring with double attaching gas chamber is designed and the main structure dimensions are ascertained.
结合膜式空气弹簧的特点，设计了一个双附加气室串联的空气弹簧，确定了主要结构尺寸。
Integrating the characteristic of diaphragm air spring, the air spring with double attaching gas chamber is designed and the main structure dimensions are ascertained.
结合膜式空气弹簧的特点，设计了一个双附加气室串联的空气弹簧，确定了主要结构尺寸。
应用推荐