Apply high strength die-casting alloy, the product features beautiful and grand.
材质使用高强度合金压铸而成，结构美观大方、防盗性强。
About half of all aluminium castings are made using high-pressure die-casting (HPDC), in which a molten aluminium alloy is injected under pressure into a steel mould, or die.
大约有一半的铸铝工艺是高压模铸(HPDC)，在这种工艺中，通过压力将液态铝合金注入钢模，或模具。
Company has mold, injection molding, metal, aluminum alloy die-casting and other ancillary works.
公司下设有模具、注塑、五金、铝合金压铸等配套厂。
Tin welding parts and lead-tin alloy die casting, zinc, beryllium bronze, phosphorus copper alloy in electroplating copper with commonly used before also gets to improve adhesion.
锡焊件、铅锡合金、锌压铸件、铍青铜、磷铜等合金在电镀前也常用预镀铜来改善结合力。
Shell aluminum alloy die-casting molding, high strength, high voltage electrostatic powder coating, corrosion resistance.
外壳铝合金压铸成型，强度高，表面高压静电粉末喷涂，耐腐蚀。
Recently, the widely applied taper runner in the world is favorable for manufacturing of zinc alloy with high quality in die casting.
目前已在世界上广泛采用的锥形流道有助于生产高品质的锌合金压铸件。
The design principle for die casting structure was summarized based on die casting characteristics and processing requirement of Mg alloy.
结合镁合金的压铸特性以及工艺要求，分析总结了压铸件结构设计原则。
Keypoints for quality control in electroplating of zinc alloy die castings are described, with stresses on the involved considerations during die designing, casting and plating pretreatment.
论述了锌压铸件电镀质量控制的要点，特别指出了模具设计、压铸及预处理等步骤中应考虑的一些问题。
Controlling deformation and flow of semisolid alloy slurry is the key of die casting of semisolid alloy.
半固态合金挤压工艺的关键是控制半固态合金坯料的流动和变形。
Failure analysis of parietal cracking in scavenging pump made of die casting aluminium alloy was carried out by means of metallographic examination, SEM analysis and so on.
借助金相显微镜、扫描电镜等分析手段，对压铸铝合金清洗泵腔壁断裂失效的原因进行了分析。
The results show that the series high temperature creep resistance die casting magnesium alloy has potential to make power-train parts with decrease of the weight greatly.
试验结果表明，所开发的抗蠕变压铸镁合金具有应用于汽车动力系统部件的制造并大幅度减轻重量的潜力。
The structural characteristics of aluminum alloy cover was analyzed, and the design of pouring system and die-casting die structure were introduced.
分析了铝合金端盖压铸件结构工艺性特点，介绍了压铸模的浇注系统及模具结构设计。
Influence of Die Casting Process on Hot-crack and its formation mechanism of AM60B alloy are discussed.
分析了AM 60 B合金热裂纹形成的机制，讨论了压铸工艺对AM 60 B合金热裂纹的影响。
At proper pouring temperature and mold temperature, the effect of die casting speed and pressure on microstructure and properties of AM60B alloy has been studied.
固定浇注温度和铸型温度，研究压射速度和压射比压对压铸am 60 B合金组织与性能的影响。
It is found that the surface defect like black stripes appeared in certain surface regions of die-casting wheel hub AM60B magnesium alloy after acid pickling in the anti-corrosion treatment.
在对AM 60 B镁合金轮毂压铸件进行表面耐蚀处理时，发现在前处理酸洗后，表面某些区域会产生黑色条纹状缺陷。
Mainly introduces the advantages of magnesium alloy and its rapid increment trend, and the design process of magnesium alloy die casting for Hitachi gear cap.
介绍了镁合金的优点及快速增长趋势，介绍了日立齿轮盖镁合金压铸件模具的设计过程。
The structural characteristics of the aluminum alloy tap part were analyzed, and the design of pouring system and die-casting die structure were introduced.
分析了铝合金水龙头零件的结构工艺性特点，介绍了压铸模的浇注系统及模具结构设计。
CAE analysis and orthogonal design are applied in aluminum alloy housing die-casting process optimization design.
采用CAE方法和正交分析法对铝合金支架压铸件的压铸工艺进行了优化设计。
The die construction, running principle and features, technological process flow, technique parameters and product performance of aluminum alloy integral naves by gravity die casting are described.
阐述了金属型铸造摩托车铝合金整体车轮的模具结构、工作原理及特点、铸造工艺流程、工艺参数及产品性能。
Although space of slider depth in aluminum alloy die casting mold are larger than the minimum values proposed by several handbooks, sometimes they are too small for pulling core.
尽管铝合金压铸模的滑块宽度间隙大于一些手册推荐的最小间隙，抽芯卡滞仍然时有发生。
The magnesium die casting and application of magnesium alloy products lead to significant amount of magnesium scrap.
镁合金铸造及镁合金产品的广泛应用造成了大量的镁合金废料。
Undertake another metal, jewelry, handicrafts and other products of zinc alloy die-casting and Epoxy.
另承接五金、饰品、工艺品等产品的锌合金压铸及滴胶。
The paper developed low-melting-Point alloy cores, through die casting experiment, the cores hole deformed well.
自行研制的低熔点合金型芯，经压铸实验，铸件孔成形完好。
The most of magnesium alloy was formed with die-casting.
镁合金大部分采用压铸技术生产。
The indirect squeezing casting process and the die structure for the Mg alloy were investigated.
研究了镁合金间接挤压铸造工艺及模具。
The billets with uniformly distributed microstructure in rheo-casting are beneficial to obtaining the A356 alloy die castings with perfect quality.
流变压铸试片的组织分布很均匀，利于获得高质量的半固态a 356合金压铸件。
The company is provided with mould development, plastics, zinc alloy die-casting, steel plate pressing, screw drawing and other workshops.
公司设有模具开发、塑料、锌合金压铸、钢板冲压、螺丝拉丝车间。
Taking the molding mould for the saddle foamed plastic pads as an example, the casting technological process for the curve-surface cavity zinc-based alloy die was stated.
以鞍座泡沫塑料垫成型模为例，阐述了曲面型腔模具的锌基合金铸模工艺，同时将三维温度场电算技术在铸模过程模拟预测中进行了有效的应用。
The paper explains the characteristics of magnesium alloy die casting parts and points out the demand for magnesium alloy die casting parts in foreign automobile trade.
文中讲述镁合金压铸件特点和国外汽车行业对镁合金压铸件的需求情况。
Different influence of Sr modification with different parameters by analyzing metallographic structure on properties of die casting al alloy is studied.
通过金相组织分析以及在不同参数下以锶变质对压铸铝合金性能带来的各种影响进行了试验。
应用推荐