A new die-casting die fit on cold chamber die casting machine was redesigned in the part of the center gate and floating flow-distribution.
分析了录音机芯飞轮压铸模的原设计失败的原因，重新设计了用于冷室压铸机的中心浇口、浮动分流的压铸模。
The problems required attention during the whole process from die-casting products design to die-casting die manufacture are introduced in detail.
详细介绍了从压铸产品设计到压铸模制造全过程中应注意的问题。
The structural characteristics of aluminum alloy cover was analyzed, and the design of pouring system and die-casting die structure were introduced.
分析了铝合金端盖压铸件结构工艺性特点，介绍了压铸模的浇注系统及模具结构设计。
Finally, taking a round electrical equipment base for example, the implement process of designing a die-casting die using the system is illustrated.
最后，以圆形电器盒底座为例说明应用该系统进行模具设计的实现过程。
On the basis of analyzing pressing parts processing characters, die-casting die parting surface is defined, die-casting die working principle is stated.
在分析铸件工艺性的基础上，确定了模具分型面，论述了模具工作原理。
Dissertation was made on the structure characteristics and principle of the die-casting die with dog-leg CAM and angle-lift splits core-pulling mechanism.
给出了实用的弯销与斜滑块抽芯结构，论述了其结构特点和工作原理。
The structural characteristics of the aluminum alloy tap part were analyzed, and the design of pouring system and die-casting die structure were introduced.
分析了铝合金水龙头零件的结构工艺性特点，介绍了压铸模的浇注系统及模具结构设计。
Because all dimension data comes from "simple handbook of die design and manufacture", the system can be regarded as a digitized design handbook about die-casting dies.
尺寸数据都来自于《模具设计与制造简明手册》，因此，本系统可以看作是一个数字化的压铸模具设计手册。
Over the analysis and improvement to the design project on die-casting die of grinding wheel machine tray, the die's working life is improved, which proves the importance of feasible design.
通过对砂轮机托架压铸模设计方案的分析与改进，延长了模具使用寿命，说明了合理设计的重要性。
About half of all aluminium castings are made using high-pressure die-casting (HPDC), in which a molten aluminium alloy is injected under pressure into a steel mould, or die.
大约有一半的铸铝工艺是高压模铸(HPDC)，在这种工艺中，通过压力将液态铝合金注入钢模，或模具。
Keypoints for quality control in electroplating of zinc alloy die castings are described, with stresses on the involved considerations during die designing, casting and plating pretreatment.
论述了锌压铸件电镀质量控制的要点，特别指出了模具设计、压铸及预处理等步骤中应考虑的一些问题。
Compared with the forging die steel, casting forging die steel although toughness is low, but high strength, red hardness is good, with low notch sensitivity and high resistance to thermal fatigue.
与锻造模具钢相比，铸造热锻模具钢虽然韧性低，但强度高、红硬性好，具有较低的缺口敏感性和较高的抗热疲劳性。
The die design and technique of gravity die casting process for driven belt wheel are introduced. The causes and corresponding resolving methods of some typical defects are analyzed.
介绍了采用金属型铸造生产铝合金驱动板的模具结构和铸造工艺；对驱动板几种典型缺陷产生的原因和解决方法进行了分析。
The thesis presents a practical die structure with Angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies.
本文给出了浮子室体铸件斜销-齿轴-齿条二级联合斜下抽芯压铸模实用结构，论述了模具结构特点和工作过程。
According to the characteristic of die casting, the mathematical model suitable for numerical simulation of die casting dies was set up and the corresponding boundary conditions were determined.
针对压铸特点，建立了适合于数值模拟的压铸摸具温度场数学模型，确定了压铸过程的边界条件。
The structure relation among various components in die casting die assemble and basic working information of the component can be easily obtained using the system.
该系统能方便地得到压铸模装配体中各零部件之间的结构关系以及零部件的基本加工信息。
A practical die structure and the process for die casting squirrel cage rotor are presented.
给出了压铸鼠笼转子的实用模具结构和压铸工艺，论述了模具的设计要点。
The design principle for die casting structure was summarized based on die casting characteristics and processing requirement of Mg alloy.
结合镁合金的压铸特性以及工艺要求，分析总结了压铸件结构设计原则。
Heat fatigue failure mechanism of the die casting dies during the process of die casting were analyzed, and the influence of optimizing process control on die life of die casting were discussed.
分析了压铸过程中模具的热疲劳失效机理及其影响因素，讨论了优化压铸过程控制对模具寿命的影响。
Mould and equipments : Die-casting mould, Low pressure casting mould, Gravity casting mould, Sand casting mould, Finish cast die, Stamping mould, Forge rolling die mould and so on.
模具及仪器类：压铸模具、低压铸造模具、重力铸造模具、砂型铸造模具、精铸模、冲压模、辊锻模等。
From the view point of casting technology, the necessity of die temperature automatic control in die casting is emphasized.
从铸造工艺角度提出了压铸型温度自动控制的必要性。
On base of the reasonable simplification to heat translating process of die casting dies, the mathematical models of temperature field of die casting die were established.
在压铸模具传热过程合理简化的基础上，建立了压铸模具温度场的数学模型。
A die casting die with pumping crossed cores by crossed compound dog-led cams and hydraulic pressure is used for cupulate parts with inboard concave.
交叉复合弯销与液压抽拔交叉型芯压铸模结构，用于压铸带内侧凹的杯形零件。
The key design points of die for direct squeezing casting and the die with two-parting surface were introduced.
给出了直接式挤压铸造模具和双分型面挤压铸造模具设计技术要点；
Introduced molding process and characteristics of ceramic die-casting technology, and pointed out prevention for the ceramic die-casting common defects.
介绍了陶瓷型铸造制模的工艺过程和工艺特点，并指出了陶瓷型铸件常见缺陷及防止方法。
The hot chamber die casting is a traditional die casting method, and there are several things that must be paid attention during the installation and operation of the hot chamber die casting machines.
热室压铸机压铸是一种传统的压铸方法，在压铸生产中有一些值得注意之处。
The key technologies for die casting die were approached from some aspects of selecting die casting machine, setting processing parameters, designing gating system.
同时，从压铸机选择、工艺参数设置、浇注系统设计角度探讨了压铸模设计关键技术。
Ltd. is specialized in the production of zinc alloy and aluminum die casting, casting machining, die casting mold development and design, and die casting product assembly.
乐清市红烨通讯有限公司是专业从事锌合金和铝合金压铸生产，铸件加工，压铸模具开发与设计以及压铸件成品组装等。
Ltd. is specialized in the production of zinc alloy and aluminum die casting, casting machining, die casting mold development and design, and die casting product assembly.
乐清市红烨通讯有限公司是专业从事锌合金和铝合金压铸生产，铸件加工，压铸模具开发与设计以及压铸件成品组装等。
应用推荐