The application and research of die casting die CAD/CAM at home and abroad are intro duced.
介绍了国外压铸模CAD／CAM的研究进展和国内已经取得的成果和研究简况。
In the design of die casting die with screw thread, the automatic screw thread unloading is a difficult point.
铸件螺纹脱模是压铸模设计的难点之一。
The automatic screw thread unloading is a difficult point in the design of die casting die for castings with screw thread.
铸件螺纹脱模是压铸模设计的难点之一。
The design process and key procedure of die casting die for throttle were described based on its structure features and technical requirements.
根据节流阀体的结构特点和技术要求，介绍了模具设计的过程和设计要点。并重点介绍了节流阀体的工艺性、分型面的选择。
A die casting die with pumping crossed cores by crossed compound dog-led cams and hydraulic pressure is used for cupulate parts with inboard concave.
交叉复合弯销与液压抽拔交叉型芯压铸模结构，用于压铸带内侧凹的杯形零件。
In order to improve the quality and efficiency on die casting die design with oblique pin drawing core, the traditional design process was optimized.
为了提高斜销抽芯式压铸模设计的质量和效率，对传统的设计过程进行了优化。
The hot dip aluminum has been carried out to research the formation and dissolution of the intermetallic layer between die casting die and aluminum alloy.
为了研究压铸模与铝合金金属间化合物的形成与分解过程，进行了热浸铝试验。
Aiming at the structure features and technological requirements for EA111 aluminum alloy oil tank, an available design plan for die casting die was described.
针对EA111油底壳铝合金压铸件的结构特点及工艺要求，介绍了一种切实可行的压铸模设计方案。
The structure relation among various components in die casting die assemble and basic working information of the component can be easily obtained using the system.
该系统能方便地得到压铸模装配体中各零部件之间的结构关系以及零部件的基本加工信息。
The die casting die with special structure for aluminum alloy thin disk was designed, and the structure features and operating principle of the die were described.
设计了一种特殊结构的铝合金薄圆盘压铸模，论述了模具结构特点和工作原理。该模具采用中心浇道，形成铸件通孔的型芯兼作分流锥。
The key technologies for die casting die were approached from some aspects of selecting die casting machine, setting processing parameters, designing gating system.
同时，从压铸机选择、工艺参数设置、浇注系统设计角度探讨了压铸模设计关键技术。
On base of the reasonable simplification to heat translating process of die casting dies, the mathematical models of temperature field of die casting die were established.
在压铸模具传热过程合理简化的基础上，建立了压铸模具温度场的数学模型。
Abstract: Through hardness testing, metallographic microscope analysis, and other means, the origination of crack failure of the aluminum alloy die casting die was analyzed.
摘要：通过硬度测试、金相组织观察，研究分析了铝合金压铸模具发生早期龟裂失效的原因。
The advantages of housing parts with aluminum alloy substituting for zinc alloy have been described, focusing on the operation and key points of design of the aluminum alloy die casting die.
分析了箱体零件由锌合金改铝合金的优点，论述了模具的工作过程和设计要点。
Hydraulic drawing-core mechanism was adopted for two-side of inner-sinking in the die casting die, and pre-resetting mechanism was set to avoid the interference of core slide with ejector pin.
压铸件内凹处两侧采用液压抽芯机构抽芯，为防止滑块型芯与推杆发生干涉而设置了预复位机构；
According to the characteristic of die casting, the mathematical model suitable for numerical simulation of die casting dies was set up and the corresponding boundary conditions were determined.
针对压铸特点，建立了适合于数值模拟的压铸摸具温度场数学模型，确定了压铸过程的边界条件。
Heat fatigue failure mechanism of the die casting dies during the process of die casting were analyzed, and the influence of optimizing process control on die life of die casting were discussed.
分析了压铸过程中模具的热疲劳失效机理及其影响因素，讨论了优化压铸过程控制对模具寿命的影响。
About half of all aluminium castings are made using high-pressure die-casting (HPDC), in which a molten aluminium alloy is injected under pressure into a steel mould, or die.
大约有一半的铸铝工艺是高压模铸(HPDC)，在这种工艺中，通过压力将液态铝合金注入钢模，或模具。
Because all dimension data comes from "simple handbook of die design and manufacture", the system can be regarded as a digitized design handbook about die-casting dies.
尺寸数据都来自于《模具设计与制造简明手册》，因此，本系统可以看作是一个数字化的压铸模具设计手册。
Keypoints for quality control in electroplating of zinc alloy die castings are described, with stresses on the involved considerations during die designing, casting and plating pretreatment.
论述了锌压铸件电镀质量控制的要点，特别指出了模具设计、压铸及预处理等步骤中应考虑的一些问题。
The key design points of die for direct squeezing casting and the die with two-parting surface were introduced.
给出了直接式挤压铸造模具和双分型面挤压铸造模具设计技术要点；
Compared with the forging die steel, casting forging die steel although toughness is low, but high strength, red hardness is good, with low notch sensitivity and high resistance to thermal fatigue.
与锻造模具钢相比，铸造热锻模具钢虽然韧性低，但强度高、红硬性好，具有较低的缺口敏感性和较高的抗热疲劳性。
The die design and technique of gravity die casting process for driven belt wheel are introduced. The causes and corresponding resolving methods of some typical defects are analyzed.
介绍了采用金属型铸造生产铝合金驱动板的模具结构和铸造工艺；对驱动板几种典型缺陷产生的原因和解决方法进行了分析。
The thesis presents a practical die structure with Angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies.
本文给出了浮子室体铸件斜销-齿轴-齿条二级联合斜下抽芯压铸模实用结构，论述了模具结构特点和工作过程。
A practical die structure and the process for die casting squirrel cage rotor are presented.
给出了压铸鼠笼转子的实用模具结构和压铸工艺，论述了模具的设计要点。
The design principle for die casting structure was summarized based on die casting characteristics and processing requirement of Mg alloy.
结合镁合金的压铸特性以及工艺要求，分析总结了压铸件结构设计原则。
Mould and equipments : Die-casting mould, Low pressure casting mould, Gravity casting mould, Sand casting mould, Finish cast die, Stamping mould, Forge rolling die mould and so on.
模具及仪器类：压铸模具、低压铸造模具、重力铸造模具、砂型铸造模具、精铸模、冲压模、辊锻模等。
Mould and equipments : Die-casting mould, Low pressure casting mould, Gravity casting mould, Sand casting mould, Finish cast die, Stamping mould, Forge rolling die mould and so on.
模具及仪器类：压铸模具、低压铸造模具、重力铸造模具、砂型铸造模具、精铸模、冲压模、辊锻模等。
应用推荐