Drill bits for dowel and bolts and cord.
钻头的销子和螺栓和脊髓。
I go to a place where a dowel splits off.
我爬到钟顶端定位梢分开的地方。
The carpenter gauged the dowel with calipers.
那木匠用卡钳估量暗榫。
Not all parts will receive dedicated dowel pin holes.
并非所有的部分将得到专门的柱销孔。
Fit a dowel pin here to keep the adjacent parts aligned.
在这里装一个定位销，是相邻的两个部件对准。
The two dowel pins align the cap and base of the housing.
用两个定位销将座罩和轴承座基础对准。
One four foot length of wooden dowel that fits inside the pipe.
一个四英尺长的木制桩相适应的管内。
Its unable to repair dowel crown because of its shorter root of tooth.
残根太短，一般无法利用桩冠修复。
Tooling Plate:Universal mounting pattern with standard dowel locating holes.
模具板：通用模式与标准安装定位桩孔。
Tooling Plate: Easy access mounting, accurate dowel location, accepts shocks.
模具板：轻松访问安装，定位准确的木钉，接受冲击。
Tooling Plate: Universal mounting pattern with standard dowel locating holes.
模具板：通用模式与标准安装定位桩孔。
Start by laying out the dowel locations every 6 in. to 8 in. along the joint.
先在要对接的边上每隔6 ~ 8英寸画一个圆榫定位标记。
Parallels with mounting keys will be doweled with a minimum . 5 diameter dowel.
带有安装健的垫脚应用销钉固定，销钉最小直径为。5.P。
Where possible screw and dowel hole clearance will be provided in the manifold.
只要可能，在分流式系统上应提供螺丝及合销孔。
Tooling Plate: Standard dowel locating holes and accurately milled locating slots.
模具板：标准定位桩孔，定位准确磨槽。
Position drive plate on the crankshaft's dowel pin and press on to the crankshaft flange.
将传动盘安放在曲轴的定位销上，然后压到曲轴法兰上。
Splitting forces are higher and dowel action is greater with the use of large diameter bars.
剪切力较高，销栓作用比大直径钢筋更有用。
Dowel pins need to be short to allow easier dis-assembly and assembly of the mould during use.
合销必须足够短，以便在使用中能更易于模具的拆卸和安装。
Objective To restore serious dental defects using reinforced fiber composite resin dowel cores.
目的利用加强纤维复合树脂桩核修复牙体严重缺损。
Also, make sure one end of the dowel is slightly ointed. This art would represent the top of the tree.
同时，要确保木钉的一端有小小的尖角，因为这代表着树木的顶部。
The device can automatically mount single part and dowel into a work - piece that contains four parts.
该装置可将单个块零件和销零件自动装配成含有四个零件的工件。
Pull out the jig dowel posts, get your hand into the sound hole and carefully peel away the cardboard jig.
拉出夹具木钉职位，进入音孔你的手，小心剥离剥夺了纸板夹具。
What would be the bottom surface of the block is then skimmed flat, and locating dowel pin holes are drilled.
将具有什么样的底部表面块然后脱脂持平，与定位柱销孔钻。
If I remember correctly, the splitter came with some kind of dowel or locking pin that just wasn't appropriate.
如果我没有记错，分配器来与一些种桩或锁定引脚，刚才是不恰当的。
The results prove these properties of converse-spine nut to be better than those of dowel joint and tenon joint.
结果证明，金属倒刺螺母螺杆连接件接口的接合性能优于直角榫接合和木螺钉接合的性能。
The dowel action of reinforcing steel bars crossing cracks is modeled for the finite element analysis of reinforced concrete.
本文提出了一个用于有限元分析的钢筋销栓作用模型。
The nonlinear vibration behaviors of a rectangular moderate thickness plate with dowel on elastic foundation were investigated.
研究了弹性地基上带传力杆的间断中厚矩形板结构的非线性振动特性。
The load transfer on dowels is modeled as vertical springs, whose stiffness depends on the dowel properties and the dowel-plate interaction.
荷载在传力杆中的传递由竖向弹簧模拟，其弹簧刚度取决于传力杆的特性以及杆与板间的相互作用。
Contractor to provide reinforcement free zones block outs dowel bar reinforcement and openings in cast in situ viaduct to facilitate interfacing.
承包商应提供无钢筋区、预留孔堵块、合缝钢筋加固和现浇高架桥内开口，以便接口。
Conclusion: the restoration of extensively damaged molars with either direct or indirect cast dowel cores can both achieve good clinical results.
结论：直接法与间接法制作分瓣桩核冠修复严重缺损磨牙均可取得良好的临床效果。
应用推荐