No endplate of reasonable size will prevent tip flow.
没有一个合适的端板尺寸将会阻止翼根绕流。
The endplate has complicated since the car's first race.
端板自第一场比赛来变得越来越复杂。
Endplate; spinal fusion; Anterior cervical approach; Reconstruction.
终板；脊柱融合；颈前路；重建。
Objective To study the role of endplate in anterior interbody spinal fusion.
目的研究椎体终板在脊柱前路椎体间植骨融合手术中的作用。
Sub-endplate PMMA augmented screw showed the least subsidence among all the screws.
终板下PMMA强化椎弓根钉的下沉位移显著低于其他固定技术。
The quantity, shape and distribution of motor endplate in the target muscle were good.
靶肌肉运动终板的数量、形态及分布良好。
Similar studies of disc and endplate were undertaken on porcine cervical spine 0 to 24 hours PM.
间盘和终板的同样研究在猪死后24小时内尸解进行。
On midsagittal images, AP dural sac diameter and the upper-endplate angles of L1 and S1 were measured.
在正中矢状位图像上测量了L1和S1水平的硬脊膜囊的前后径和上终板角。
The high strength bolts resistance on the steel beam-to-column extended endplate connection is studied.
方法采用考虑接触和螺栓预拉的非线性有限单元法对不同构造的梁柱外伸端板连接进行分析。
ResultsThe stress mainly distributed in the endplate and lumbar disc, especially in the posterior part.
即时显示手法作用时腰椎各结构内在应力的变化。
Results The stress mainly distributed in the endplate and lumbar disc, especially in the posterior part.
结果应力变化主要集中于终板及椎间盘，以后部更为明显；
Objective To evaluate the therapeutic effect of Shuyao Mixture on the aging of vertebral endplate in rats.
目的评估舒腰合剂抗老龄雌性大鼠椎体终板老化的作用。
The stress distributed in the left-posterior part and the right-anterior part of the endplate and lumbar disc.
应力在终板和椎间盘上又集中左侧后部和右侧前部，外层的应力大于内层；
Objective: to understand the effects of exogenous androgen on the skeletal muscle fiber and its motor endplate.
目的：观察雄激素对骨骼肌肌纤维及其运动终板形态的影响。
Objective To explore measures to prevent motor endplate degeneration and muscular atrophy after motor nerve injury.
目的本研究旨在探讨运动神经损伤后运动终板退变的预防方法。
This is based on the previous version, but it has been simplified with no upper flaps and a multiple endplate section (bottom arrow).
此款前翼去掉了上层翼片并且使用了多段板的设计（箭头所示）。
Adolescent vertebra was on the stage of maturing, and the growth cartilage of endplate is the most weak part of vertebra motion unit.
青少年椎体处于发育成熟阶段，软骨终板分为关节软骨层和生长软骨层。
The lumbar endplate chondrocyte was cultivated, it's characteristic of cell biology was observed and it's cell phenotype was identified.
培养大鼠腰椎终板软骨细胞，观察细胞生物学特性，并行细胞的鉴定。
Methods. We evaluated the presence of endplate sclerosis, osteophytes, and narrowing of disc Spaces in 434 Japanese postmenopausal women.
方法：我们评价了434名绝经后日本女性终板硬化，骨赘，椎间隙狭窄的发病情况。
Objective: To investigate the effects of variations in vertebral endplate concavity on the mechanical behaviors of the lumbar motion segment.
目的：研究终板凹陷程度变化对腰椎运动节段生物力学影响。
It was found to be associated with expansion of the intervertebral disc, which was likely to be secondary to changes in the vertebral endplate.
我们发现骨质疏松伴有椎间盘的膨胀，而这可能继发于椎体终板的改变。
Study Design. A retrospective observational study of healthy volunteers and patients with degenerative and infectious endplate abnormalities in the lumbar spine.
研究设计：对健康志愿者以及退变性终板异常和感染性腰椎终板异常患者的回顾性观察研究。
Conclusion: Swimming training with loads promotes transformation of the muscle fiber types and increases the diameters of the muscle fiber and the endplate as well.
结论：游泳训练，尤其是加负荷的游泳训练可以促进骨骼肌肌纤维类型的转变，也可以扩大肌纤维和运动终板的直径。
Objective To measure and compare the biomechanical properties of two different types of sacral screw fixation either through the superior endplate or anterior cortex.
目的测试骶骨螺钉经上终板固定技术的生物力学性能，并与经前皮质固定技术比较。
Intradiscal leakage on the l2-l4 level may be inevitable to obtain appropriate mechanical properties in the case of severe endplate breakdown connected with the disc space.
在l2—l4节段如果终板破裂情况下，要恢复机械力学，盘内骨水泥渗漏可能是不可避免的。
BACKGROUND: Proteoglycan is the main component of cartilage endplate, which is the biochemical basis in maintaining the biomechanical behavior of cervical intervertebral disc.
背景：蛋白多糖是软骨终板的主要组成部分，是维持椎间盘力学性能的生化基础。
A dynamic pressure generating groove 12 is formed on the lower end surface of sleeve 5, and a dynamic pressure generating groove 13 is formed on the upper surface of the endplate 7.
动压力产生槽(12)形成于套筒(5)的下端表面上，并且动压力产生槽(13)形成于端板(7)的上表面上。
A dynamic pressure generating groove 12 is formed on the lower end surface of sleeve 5, and a dynamic pressure generating groove 13 is formed on the upper surface of the endplate 7.
动压力产生槽(12)形成于套筒(5)的下端表面上，并且动压力产生槽(13)形成于端板(7)的上表面上。
应用推荐