High speed cutting and finish milling with high feed rate.
高速切削且能以高迸给率精铣。
Especially for cutting the material in high speed and feed rate.
尤其是切割速度和进料速度比较高。
The coal feed rate and the size of the grinding table are variable.
饲料粒径大小随鱼的生长而增大,并维持在鱼种口全开时的一半左右。
When the velocity (feed rate) is not constant, several problems can result.
当进给速度不恒定时,会造成许多问题。
From the model, the effects of the dip Angle and feed rate on thrust force are estimated.
在此基础上,分析比较了进给量、斜面倾角等参数对斜面钻孔初期受力的影响。
Drip-feed rate has a definite effect on the chemotherapy of patients with cardict and cancer disease.
输液速率的快慢对于患有心脏疾病和癌症病人化疗时具有一定的影响。
The influence of cutting speed and feed rate on the surface roughness of machined blade was investigated.
研究了切削速度和进给量对加工表面粗糙度的影响。
It was found that feed rate affected the secondary reaction in the pyrolysis furnace and the main product.
研究发现,进料量影响了炉管内的二次反应,进而对主要产物收率有重要影响。
Rotate, pressure of 4th, pressure of 5th and degree of two-section pressure increase with feed rate increasing.
随着喂料速度升高,扭矩、4区压力、5区压力、两区压力差呈现大致升高的趋势。
The effects of temperature, the quantity of catalyst used, and reactant feed rate on hydrosilylation was discussed.
考察了温度、催化剂用量、加料速率等因素对苯乙烯与甲基二氯硅烷硅氢加成反应的影响。
Results of VMD experiments indicate that flux increases when feed temperature, feed rate and vacuum degree increase.
实验表明,随进料温度、进料流速、冷侧真空度的增大,膜通量增大;
The catalyst quantity, alcohol-acetic mole ratio, feed rate and reflux feed site effects on the process are investigated.
对醋酸与正丁醇酯化反应体系,考察了催化剂用量、醇酸比、进料流量、进料位置、回流位置等因素对过程的影响。
The influence of different cutting speed and feed rate on the roughness of vane's finished surface was investigated and analyzed.
研究分析了不同的切削速度及进给量对叶轮叶片加工的表面粗糙度的影响。
Wet pellet, feed is superior to dry pellet feed in aspects of palatability, seductions, feed rate and digestible absorptivity of protein.
湿性颗粒饵料在适口性、引诱性、摄食率、蛋白的消化吸收率等方面都比干性颗粒饵料有所提高。
The technological parameters such as electrolysis current, the rotation speed of grinding wheel and the feed rate etc, have been optimized.
研究了砂轮转速、进给量等工艺参数对石英玻璃表面粗糙度的影响;
Due to low load operation, the inspection intervals shall be shortened, the maintenance intervals shall be reviewed, and the feed rate of Cyl .
由于低负荷操作,可以预先知道引起油头、燃烧室、增压器、透平的脏堵,检查周期须缩短,维修保养周期须更新,汽缸油供给率须调整。
Two groups of matching relation of the weld speed and the wire feed rate were found in a condition of invariable laser power and focus position.
前者试验获得了一定激光功率和离焦量条件下两组焊接速度和送丝速度的匹配关系,并发现填充焊丝的加入对焊缝咬边现象确有改善;
A new developed instrument Model CSY-1 for measuring wire feed rate in MIG and MAG welding and for detecting quality in welding process is given.
新研制的、适用在MIG、MAG焊接中,作测定送丝速度和在焊接生产中作质量检测的CSY一1型测量仪。
The larger the variation of amplitude and frequency of time-varying feed rate, the better the effect of suppressing chatter under some conditions.
在一定的条件下,时变进给量变化幅度及变化频率越大,抑振效果越好。
To improve the efficiency decreased by feed rate in traditional nc program, a nc program optimization system is developed for rough milling process.
针对传统数控程序中进给速度固定限制加工效率的缺点,开发了面向粗铣加工的数控程序优化系统。
The interpolation precision is correlated with Max feed rate pulse equivalent of CNC cyc of interpolation and output impulse frequency of pulse generator.
其插补精度与最大进给速度、机床系统的脉冲当量、插补周期,以及脉冲发生器的输出脉冲频率有关。
The droplet transfer cycles were controlled by wave control method. Also gradual adjustment of the sequential and wire feed rate was controlled by software.
采用波形控制方法对熔滴过渡周期进行控制,同时软件还对时序系统和送丝速度进行精密渐变控制。
The influence of the factors, such as the molar ratio of acetic acid ton-butanol, the feed rate of the reactants and packing density of the catalyst, was investigated.
考察了酸醇投料摩尔比、混合液的进料流量、催化剂的填充密度等因素对反应过程的影响。
The technics parameters, such as the laser power, scan velocity, powder feed rate and the Z axis increment, which influence quality and shape were analyzed in this article.
分析了主要工艺参数如:激光功率、扫描速度、送粉量以及Z轴增量对成型质量和形貌的影响。
The emulsifier content and feed rate affect latex swelling and shell polymerization by the making a change of latex number and total reaction rate coefficient respectively.
乳化剂量和加料速率分别通过影响胶粒数和总体反应速率系数而对胶粒溶胀和壳层聚合反应产生影响。
Using Taguchi method to optimize the operation about the depth of cut, the spindle speed and the feed rate. Then the optimal cutting parameters can be drawn after analysis.
应用田口法分析主轴转速、背吃刀量和每齿进给量三个可控因素对表面粗糙度的影响,经过分析可以得出最优的参数组合。
High productive machining i. e. machining with faster production cycle is a comprehensive technology, in which increasing cutting speed and feed rate are merely two components.
高速加工即以较快生产节拍进行加工,提高切削和进刀速度是其系统技术中的一个环节。
High productive machining i. e. machining with faster production cycle is a comprehensive technology, in which increasing cutting speed and feed rate are merely two components.
高速加工即以较快生产节拍进行加工,提高切削和进刀速度是其系统技术中的一个环节。
应用推荐