This method is more suitable for pump cavitation performance curve fitting.
该方法较适合于泵汽蚀性能曲线的拟合。
On the basis of Chebyshev curve fitting method, a new method to design worn profile tread is proposed by this paper.
本文在切比雪夫曲线拟合方法的基础上，提出了一种高次曲线磨耗形踏面的设计方法。
An example calculated shows that this method is even more simple, convenient and reliable than the traditional curve fitting method.
实例计算表明，本方法比传统的曲线拟合方法更为简便可靠。
In this paper, a general method for meta-graph recognition is proposed based on curve fitting and separation of line and smooth curve.
本文针对图纸矢量化中的图元识别技术，提出了系统的基于线弧分离和拟合识别方法。
Gives a new curve fitting method for non linear sensor.
介绍了非线性传感器的一种曲线拟合方法。
Conclusion the polynomial fitting curve is the perfect linear evaluation method. It guarantees both the accuracy and reliability of the experimental results, and is more suitable to clinic.
结论多项式拟合曲线是较为理想的线性评价方法，既保证了实验结果的准确性、可靠性，而且更适用于临床。
Gives a new curve fitting method for non - linear sens or.
介绍了非线性传感器的一种曲线拟合方法。
Based on the idea of curve fitting this paper proposes a new method for calculating the balancer in partial inertia force balancing of planar linkage mechanisms.
本文根据曲线拟合的思想提出了一种解决平面杆机构惯性力部分平衡配重计算的新方法。
This article introduces the MATLAB curve fitting toolbox, and provides a special application method through the test data processing of Automobile surface modeling.
介绍了MATLAB曲线拟合工具箱，并通过汽车覆盖件的曲面造型测试数据的处理，给出了具体的应用方法；
A response curve fitting method is developed to estimate parameters of beam-type members with unknown rotational response.
针对结构中的梁式构件提出了一种基于反应曲线拟合的参数识别方法。
By using curve fitting theory, proposed a new method of power quality detection.
根据曲线拟合的概念，提出了一种新的电能质量检测的去噪算法。
A novel IR object tracking method which combines curve fitting and correlation matching is presented.
给出了一种将曲线拟合和相关跟踪相结合的红外目标跟踪算法。
Moreover, this paper puts forward an adaptive method of control valve based on open-loop and enhances measure accuracy through curve fitting method.
同时，本文提出一种基于开环的阀门开度自适应控制方法，通过在线曲线拟合的方法提高阀门控制的精度。
A new curve fitting method using area error feedback based on cubic splines is presented.
本文提出一种新的基于三次样条曲线的面积误差反馈曲线拟合方法。
Consequently, with the use of curve fitting method, the inversion of all seismic lithologic parameters can be easy achieved, and zero-offset section can be obtained.
所以利用曲线拟合方法很容易实现全部地震岩性参数的反演，并可提取零偏移距剖面。
Methods the measurable range was broadened through: Lowering of the specific radioactivity of the labelled antigen, increasing the concentration of the anti-serum and improve the curve fitting method.
方法：通过降低标记抗原的比放射性，提高抗血清的浓度，改进曲线拟合方式等方法，扩大测定范围。
Conparing with the conventional curve fitting, this method is simpler, the matched curve could be obtained by only giving the data points and the acceptable error.
与传统的曲线拟合方法相比，该方法只需给定数据点及允许误差即可得到匹配的曲线方程。
Polynomial curve fitting is a usually used data fitting method. When there are too many data for fitting, only just one polynomial curve function cannot acquire good fitting effect.
多项式曲线拟合是一种较常用的数据处理方法，但当数据点较多时，只采用一种多项式曲线函数拟合所有数据点难以取得较好的拟合效果。
Reasonable curve fitting method were selected.
选择了合理的计算方法。
Both the wavelet functions and the least square algorithm of fitting of data are used to construct a new method of fitting of curve and surface.
本文把小波函数引入离散数据拟合领域，将小波函数与数据拟合的常用方法——最小二乘法相结合，给出了一种新型的数据拟合工具。
The fitting performance curve equation method has studied with emphasis.
重点研究了拟合性能曲线方程的方法。
On the basis of short straight-line fitting, this dissertation USES the least-square method of curve matching to discern circle and straight line.
通过对离散点进行短线段拟合的基础上，再利用曲线拟合的最小二乘法对圆和直线进行二次拟合。
A new feature-points extraction algorithm is proposed, which USES least square method fitting contour curve and combines slope, curvature information to extract feature-points.
提出一种新的轮廓特征点提取方法，它利用最小二乘法拟合轮廓曲线，结合斜率、曲率信息提取特征点。
Both the rational functions and the least square algorithm of fitting of data are used to construct a new method of fitting of curve and surface.
把有理函数引入离散数据拟合方法中，将有理函数与数据拟合的常用方法——最小二乘法相结合，给出了一种新型的数据拟合工具。
Then, using curve fitting and optimization method, the linear model, hysteresis model and variable linear model of pressure-torque relations are developed based on test data.
其次，在获得大量试验数据的基础上，运用曲线拟合和优化技术，建立制动压力-力矩关系的线性模型、迟滞模型和可变线性模型。
Some curve surface fitting methods used in the reverse engineering are analyzed, and a new free curve surface fitting method based on ANN is presented.
分析了应用于反求工程的几种曲面拟合方法，提出一种基于神经网络技术的自由曲面拟合新方法。
By using the method of curve fitting to calculate the traction tonnage, we can gain the traction tonnage within short time and short distance after the locomotive start.
对牵引吨位的计算，采用了曲线拟合的计算方法，能够在列车起动最短的时间、运行最短的距离内计算出牵引吨位。
By using the method of curve fitting to calculate the traction tonnage, we can gain the traction tonnage within short time and short distance after the locomotive start.
对牵引吨位的计算，采用了曲线拟合的计算方法，能够在列车起动最短的时间、运行最短的距离内计算出牵引吨位。
应用推荐