High precision special crown gear teeth.
高精度专用冠齿轮牙齿。
齿轮互相啮合。
Exact modeling of gear teeth is based on meshing theory.
摘要根据齿轮啮合原理，建立了轮齿的精确齿形。
Based on gear engagement theory, the exact model of gear teeth is produced.
根据齿轮啮合原理，建立了轮齿的精确齿形。
Just like with spur gears, the solution to this problem is to curve the gear teeth.
就像直齿轮一样，这个问题的解决也是将轮齿变为曲线。
In this paper reasons of premature failure of gear teeth of coal mining machinery are analyzed.
本文分析了煤矿机械齿轮早期断齿的原因。
The test of Pb samples indicates that the die set works smoothly and gear teeth are filled fully.
根据铅试样模拟实验表明，模具装置工作顺畅，齿轮成形饱满。
The gear teeth engagement of gear transmission was being studied as a Non-Hertz elastic contact problem.
并采用赫兹接触理论和有限元方法分析渐开线齿轮的接触应力。
To transmit motion smoothly, the contacting surfaces of gear teeth must be carefully shaped to a specific profile.
为了平顺地传递运动，齿轮齿的接触面必须精加工成特殊齿廓。
Disadvantages: the gear teeth due to smaller displacement volume and will wear, so can only transport clean fluid;
齿轮泵缺点：由于较小的置换容积以及会磨损齿牙，所以只能输送干净的流体；
The gear teeth and meshing line are distorted in the meshing process as a result of wearing and rise in temperature.
实际应用中，由于磨损和受热等原因，使得齿轮齿廓以及啮合过程中啮合线都发生了畸变。
The initial contact of helical gear teeth is a point, which changes into a line as the teeth come into more engagement.
斜齿轮轮齿的初始接触是一点，当齿进入更多的啮合时，它就变成线。
Following the rules of machining and outspread principle of involutes, the mathematical model of spur gear teeth profile is built.
根据齿轮加工原理及渐开线展开原理，建立了直齿轮齿廓的数学模型。
Commonly used targets include gear teeth, slotted discs, shafts with keyways, etc. made of carbon steel, iron, or magnetic stainless steel.
常用的指标包括与键槽齿轮，开槽盘，轴等的碳素钢，铁，或磁性不锈钢制造。
Milling can produce flat or angled surfaces, groves, slots, gear teeth, and other profiles, depending on the shape of the cutters being used.
铣削可根据所用的铣刀形状分别加工平面或斜面、槽口、缝、齿轮齿及其它型面。
The internal teeth of the ring gear mesh with the planet gear teeth. Thus, the ring gear rotates with the other parts of the planetary gear system.
内齿圈的内齿与行星轮的齿啮合。因此，内齿圈随着行星轮系统的其他配件旋转。
By strengthening under low amplitude loading, bend fatigue strength and life of gear teeth can be increased by 3.97 and 109 percents, respectively.
经过低幅载荷强化，该齿轮轮齿的弯曲疲劳强度提高了3.97%，弯曲疲劳寿命提高了109%。
Based on the broken gear teeth in contact fatigue test, bending fatigue life curve was got by applying finite element stress analysis results, MSC.
本文以接触疲劳试验中疲劳断齿齿轮为依据，利用有限元应力分析结果以及试验得到的弯曲疲劳寿命曲线，应用msc。
Interval optimization method is convenient for making the products series. The problem of the number of gear teeth matching in drive train was solved.
区间优化方法便于产品的系列化，可以解决传动系齿轮配齿问题。
On the basis of analysis of gear teeth strength, gear power capacity rating and profile correction, as well as vibration and noise of gearing, are studied.
齿轮强度分析是轮齿承载能力、振动、噪声及修形等研究的基础。
Straight bevel gear teeth actually have the same problem as straight spur gear teeth-as each tooth engages, it impacts the corresponding tooth all at once.
直齿锥齿轮和直齿轮存在这同样的问题----齿的啮合过程中始终存在冲击。
Shaving is one of the most widely used methods for finishing gear teeth, and the plunge shaving method is a more efficient process for finishing gear teeth.
剃齿加工是齿轮精加工的一种工艺方法，而径向剃齿法是剃齿工艺中一种更加高效的齿轮精加工工艺。
The cause which result in breaking off gear teeth and vanes touching wall on high load are analyzed, according to the stress status of gear and axle in Root's blower.
根据罗茨风机齿轮、轴受力情况，分析高负荷下风机齿轮轮齿折断及叶轮擦墙板的原因。
A sine wave alternating voltage signal is generated synchronously in the presence of gear teeth made of carbon steel, magnetic stainless steel, or iron (ferrous metal).
阿正弦波交流电压产生的同步信号中的齿轮碳钢，不锈钢磁性，或铁(黑色金属)提出的存在。
Surface temperature on gear teeth was measured by dynamic thermocouple method. A test gear construction consisting of three pieces and electric resistance was designed.
用动态热电偶法测量齿面闪温分布，设计制造可测出全齿面闪温的三片组合带电阻式齿轮结构。
A lot of determination schemes of the number of gear teeth can be obtained quickly with this method so that a basis for schemes comparison and optimum design is established.
该设计方法可在较短时间内找到较多的齿数设计方案，为进行多方案比较和优化设计打下了基础。
During the cutting of the worm bevel gear, due to the impact interference between the worm and cutter rest slide and screw, the gear teeth shape cutting can not be performed.
蜗杆伞齿轮切齿时，由于蜗杆部分与刀架滑板及刀架螺钉发生碰撞干涉，导致刨齿加工无法顺利进行。
Based on the experimental results, the relationships between bend fatigue strength, life of the gear teeth and strengthening loads as well as strengthening cycles are obtained.
在试验结果的基础上，得到了该齿轮轮齿弯曲疲劳强度、弯曲疲劳寿命随低载强化次数和强化载荷变化的函数关系。
Based on the experimental results, the relationships between bend fatigue strength, life of the gear teeth and strengthening loads as well as strengthening cycles are obtained.
在试验结果的基础上，得到了该齿轮轮齿弯曲疲劳强度、弯曲疲劳寿命随低载强化次数和强化载荷变化的函数关系。
应用推荐