The emphasis is placed on the predictions of the heat transfer rate on the wall.
计算的重点放在壁面热流率的预测。
The experiments show that the heat transfer rate in the porous bed is mainly influenced by…
实验表明，多孔物料床的沸腾换热强度主要受到颗粒—液体组合的影响。
Additionally, it can only apply to one layer insulation and cannot predict the heat transfer rate after insulation.
此外，只能限于包一层隔热材和无法对隔热材包覆后之散热率之作正确估算。
The oil flow rate distribution curve mainly has an "S" shape, and the heat transfer rate shows a "bathtub" distribution.
油冷器各层芯片流量分配曲线大致呈S形分布，而换热量分配曲线呈浴盆状分布。
Usually, it also causes the wall heat transfer rate to decrease somewhat in the region downstream from the point of separation.
通常，它也会使分离点下游区间内的壁热交换率有所减少。
It is a new technology to sinter ceramic materials rapidly by means of the high temperature and high heat transfer rate of plasma.
利用等离子体的高温和高传热率快速烧结陶瓷材料是一项新技术。
Relationship of heat transfer rate and filling rate is obtained, as well as the relationship of velocity and inner diameter, filling rate.
最后，对脉动热管的传热规律作了初步分析，得出了传热性能与充液率的关系，以及运行速度与管径，充液率的关系。
Numerical results indicate that there is an optimum mass fraction of multiple PCMs for the LTES system to reach the maximum heat transfer rate.
数值结果表明，存在一个最佳的质量分数的多个为LTES系统的相变材料来达到最大的热传递率。
And the relations between heat transfer rate and charging ratio, cooling, method, relative position of heating end and cooling end etc was investigated;
研究了其传热性能与充液率，冷却方式，加热端与冷却端相对位置等各种因素的关系；
It is analyzed that the thermal and chemical model have a effect on the shock detached distance, heat transfer rate, the distributions of temperature and density.
分析了各种气体模型对激波脱体距离、壁面热流、温度分布和密度分布等的影响。
The numerical and analytic results show that the heat transfer rate obtained by potential capacity dissipation minimization is better than that by entropy generation minimization.
数值计算和理论分析的结果表明，根据最小传递势容耗散原理得到的结果优于最小熵产原理得到的结果。
The results show that the heat transfer rate in a pulsed fluidized bed is 15%greater than that in a normal fluidized bed. The bigger the particles, the higher the heat transfer efficiency.
对脉动流化床内换热面与床层的传热特性进行了试验研究，试验中观察到的脉动床最大传热速率比普通流化床的传热速率提高15%左右，对于较大直径的颗粒，脉动流化床的传热效果更突出；
Through a test research for heat pipe radiators of steel column type, we get the relative formula of heat transfer rate, calculating temperature difference and flow rate of the heat medium.
通过对钢制柱型热管散热器的试验研究，得出了散热器热流量和计算温差、热媒流量的关系式，并提出了进行热工性能试验的方法及进一步研究的意见。
The boiling heat transfer rate in a narrow gap is much higher than that in a pool, and its heat transfer mechanism is dominated by the evaporation of thin liquid film under deformed bubbles.
狭窄空间中的池沸腾传热强度高于大空间池沸腾，其主导传热机理是受压变形气泡底部的微液膜蒸发机理。
As wind speed increases, so does turbulence, and thus the rate of heat and moisture transfer.
随着风速增加，湍流也变得更强烈，因此热量和湿度的比例得以转移。
The heat will readily transfer from the plastic to the mold but getting it from the mold and into the coolant at the same or greater rate is frequently the problem.
热量从塑料传输到模具，而从模具得到热量并同时或者以更大的速率传导到冷却剂则常常成为问题。
Therefore, the control of both temperature and heat-transfer rate is extremely critical during the formation of pitch-based carbon fibers.
因此，在沥青基炭纤维形成过程中，控制温度和传热速率是极为关键的。
At a given air inlet condition and airflow rate, meanwhile, dryness of air outlet was required, proper heat-transfer area and matching refrigeration system are obtained through calculating.
在一定的进气状态下，为达到要求的出气干度，对给定的空气流量进行了设计计算，以得到合适的传热面积与制冷系统的匹配。
The first question concerns thermodynamics, the second the various rate processes- -chemical kinetics, heat transfer, etc.
第一个问题涉及热力学，第二个问题涉及各种速率过程——化学动力学，传热等。
If this causes a warpage problem, it sometimes helps to raise the overall water temperature and slow the rate of heat transfer.
如果这样还有翘曲问题，那么升高总的水温并降低热交换速度是有益的。
The influence of operating conditions on mass transport rate and evaporation efficiency was discussed by applying traditional mass and heat transfer theories to membrane.
实验还考察了料液温度和流率对膜通量及热效率的影响，利用膜及膜两侧边界层内传热传质理论对此进行了分析讨论。
A two-phase flow patterns, the relationship between the heat transfer coefficients and heat flux and the relationship between the recirculation flow rate and heat flux are investigated.
探索了该装置内的两相流流型及传热系数、循环速率与热通量的关系。
A mathematical model for heat transfer process in HPH furnace was established and verified, then applied to analysis of the relationship between gas flow rate and annealing time.
通过建立全氢罩式退火炉炉内传热过程的数学模型，并经过实测验证后，分析了循环风量与退火时间的关系。
The rate of heat transfer in mould affects significantly on the surface quality of slab and protection of steel breaking in continuous casting.
在连铸过程中结晶器的传热速率对铸坯的表面质量和防止漏钢都具有十分重要的影响。
The test results show that the impingement heat transfer from the rib roughened surface is considerably affected by the initial crossflow rate.
实验结果表明，初始横流率对肋粗糙表面的冲击换热有重要的影响。
The result shows that the preferable heat transfer effect can be acquired on the condition of a low flow rate.
研究结果表明流体绕流振动圆管时，在较低流速下即可获得较好的传热效果。
The result shows that the preferable heat transfer effect can be acquired on the condition of a low flow rate.
研究结果表明流体绕流振动圆管时，在较低流速下即可获得较好的传热效果。
应用推荐