The impact scraping load displacement curve and scraping work can be measured by the machine.
测试涂层冲击刮削载荷—位移曲线及刮削功等。
Meanwhile, possible patterns of simplifying the calculation for load displacement are also studied.
同时还探讨了载荷位移的简化计算的规律。
This paper deals with the load-deflection and load displacement curves of beams basedon the fatigue experiments of plated and unplated RC beams.
本文通过钢筋混凝土芯梁及粘贴钢板补强混凝土复合梁的疲劳试验，研究了它们在疲劳试验过程中载荷和加载线位移及跨中挠度的变化规律。
The load displacement curve under static load, load displacement hysteric curve under repeated low cycle load and strain data at key points are presented.
给出了静力荷载下的荷载变形曲线、低周反复荷载下的荷载变形滞回曲线以及关键部位的应变数据。
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；
The expressions of load, displacement, stress and residual stress distribution for hole cold_extrusion process are established by using elastic_plastic theory.
利用弹塑性理论建立了孔冷挤压的载荷、位移、应力以及残余应力分布表达式；
The load that must be applied to enforce this displacement rate varies as the test proceeds.
随着实验的进行，用来产生位移的载荷是随位移的变化而变化。
Because of its excellent part load efficiency, many compressor unit is used mainly in the occasions for large displacement in high pressure piston compressor applications.
由于其出色的部分负荷效率，多压缩机机组主要应用于的场合为大排量中高压活塞式空压机应用领域。
The relation between load and displacement is deduced by approximately differential equation of flexural curve and the error resulted from this estimation is given out.
应用挠曲线近似微分方程，推导了线切割结构的载荷与位移关系，并给出了由于微分近似导致的误差。
By this equation, we can calculate the displacement, load and dynamometer diagram at every rod node and any time.
通过求解该方程，可计算各节点不同时刻的位移，计算出载荷，绘出各节点功图。
The key of push-over analysis method is load pattern and target displacement.
推倒分析中的关键是加载模式的选取和目标位移的求取。
By using ANSYS5 7 software, the relationship between load and displacement of Bourdon tube can be analyzed quantitatively by entering modeling pattern and design parameters.
利用ANSYS57软件，输入建模方式及设计参数可对弹簧管的载荷与位移间的关系进行定量分析。
The displacement load equations were derived by differentiating with respect to total potential energy in spline displacement function of a strip.
首先对条单元以样条位移函数表达的总势能进行求导而推导了位移-荷载关系式。
Make the three-dimensional finite element model about plate rubber expansion device. And then the models are applied serviceable load and displacement.
建立板式橡胶伸缩装置的三维有限元模型并施加符合实际工作状况的载荷与位移边界条件。
In the problem of how to judge distortional buckling, a good method is use load-axial displacement curve.
在畸变屈曲的判断标准的问题上，可以采用荷载—轴向位移法，亦可以采用荷载—横向应变法。
Based on finite element simulating tests of frame columns, load-displacement of frame columns without tests are simulated, and the influencing factors of frame columns are synthetically analyzed.
在有限元模拟试验框架柱的基础上，还对未做试验的框架柱进行了骨架曲线的模拟，从而对影响框架柱的各因素进行了综合分析。
And under earthquake load, the maximum displacement of dam top is larger.
且在地震荷载作用下，坝顶最大动位移增大。
The testing machine is equipped with load, displacement, strain and vibration test systems and corresponding data processing software.
并配备有荷载、位移、应变和振动测试系统及相应的数据处理软件。
The relations between uplifting load , displacement and time were simulated numerically and compared with the results of actual pile tests, and the ultimate uplifting bearing capacity was defined.
数值模拟了上拔荷载、桩上拔位移与时步的关系，并与宏观物理实物试验的实测结果作了对比分析；
The load point displacement caused by single load for two dimentional cracked body with certain strain hardening exponent is divided into its linear-elastic and plastic components.
将具有一定应变硬地指数的二维裂纹体在单一载荷作用处的位移分成线弹性部分和塑性部分。
The loading frame can work in either load-control or displacement-control mode, and signals from the load sensor are digitalized with the control computer.
通过计算机控制，加力机构可以对微小试件按力或位移控制方式加载，载荷大小通过传感器直接由计算机数字化。
The paper analyzes mechanism of action and load transfer under group anchor, calculates load transfer-displacement by shearing displacement-transfer function method.
通过对群锚作用下的作用机理、荷载传递进行分析，使用剪切位移—传递函数法进行荷载传递位移计算。
The axial compressive load-displacement curves and damage patterns are compared between the hollow thin wall metal cylinders and the thin wall metal cylinders filled with polyurethane foam in test.
试验比较了空心薄壁金属圆筒和充填聚氨酯的薄壁金属圆筒的轴向抗压荷载-位移曲线和破坏模式。
The influence of eccentricity on the configuration of load-displacement and mean crush load was discussed.
讨论了偏心率对平均压缩载荷和载荷-位移曲线形貌的影响。
The failure process and mode has been observed, and load-displacement curves, cracking and ultimate load, and the strain of longitudinal and transverse steels have been recorded.
试验中，观测了试件的破坏全过程及破坏形态等，记录了荷载—位移滞回曲线、开裂荷载、极限荷载、箍筋和纵筋的应变等数据。
Numerical method is used to analyze the load-displacement hysteretic behaviors of concrete-filled circular steel tubular beam-columns in this paper.
本文采用数值计算方法，对圆钢管混凝土压弯构件荷载-位移滞回关系曲线进行了理论分析。
Numerical method is used to analyze the load-displacement hysteretic behaviors of concrete-filled circular steel tubular beam-columns in this paper.
本文采用数值计算方法，对圆钢管混凝土压弯构件荷载-位移滞回关系曲线进行了理论分析。
应用推荐