And we have, if you will, a low pressure injection system that will also provide water into the core for low pressure. And we have boron that's capable of being inserted as well, as needed.
如果你们可以，一个低压力的加入系统，会给低压力的核心提供水，我们还有硼，它也是可以，被加入的，也是需要的。
This system is used to pump water into the core, low pressure safety injection and high pressure safety injection.
这个系统是用来将水抽到核心里去，降低压力安全加入和高压力，安全加入。
The active systems consist of several pumping systems of varying discharge pressure and flow rates, e. g., high head injection system, low head injection system.
能动系统由不同注入压力和流量的泵系统组成，如高压安注系统，低压安注系统。
Water injection efficiency depends on whether the injection pressure is high or low in water injection Wells.
注水井注水压力的高低直接影响水井的注水效率。
Liquid silicon rubber injection moulding has constant cooling pressure to the cable. It is Low in electricity output while "breathing" together the cable.
液体硅橡胶注射成型对电缆本体有恒定的收缩的收缩压力，与电缆同“呼吸”局部放电最低。
The injection molding test has been carried out - the test shows that the injection pressure is low, the forming cycle is short and the production efficiency is high.
试验表明热流道注射成型注射压力低、成型周期短、生产效率高。
The sensitivity analysis indicates that the parameters impacting the production results from high to low are production time, steam dryness, cyclic steam injection volume, steam injection pressure.
敏感性分析表明，蒸汽参数对开发效果影响的顺序从大到小依次为生产时间、注汽干度、周期注汽量、注汽压力、焖井时间和注汽速度；
Liquid injection molding utilizes low viscosity silicones which can be pumped at lower pressure and temperature, and cure in significantly less time and with less waste than solid materials.
液体侵渍模塑使用低粘度的硅树脂，在低压和低温条件下抽运，在极短的时间内固化，与固体材料相比，废弃物少。
This through injection molding machine with low noise, pressure stability, low power, high efficiency advantages.
今通注塑机具有低噪音、压力稳定、省电、高效率的优点。
Analyse the process of the low-pressure reaction injection molding for rapid tooling, and summarize the quality fish-bone diagram through the lifecycle of product.
对面向快速模具的低压注型工艺进行分析，总结出其整个生命周期中影响其质量的产品质量鱼骨图。
The failure mode and consequence that the low pressure safety injection system may occur, and the measure to improve the reliability of the system is analysed in this paper.
本文分析了低压安全注射系统可能发生故障的原因与后果，以及提高其安全可靠性所采取的措施。
This zone has the features of poor property, poor communication and low energy, and pressure is not affected by water injection well.
其特点是物性差、连通性差、能量小和压力不受注水井影响。
But the fuel starting injection pressure will turn low gradually when the operational time of the diesel engine increases. This will cause worsening of the combustion process and fuel economy.
但是随着柴油机使用期的增长，启喷压力会逐渐降低，导致燃烧过程恶化，经济性下降。
Theoretical result shows that even in a very low admixture injection pressure, fracturing will occur in surrounding soil.
理论分析发现即使在很小的固化剂注入压力作用下，周围土体也会发生劈裂现象。
Injection realize, in the pressure cooling, the use of low temperature water to mold a cooling cuisine, so as to narrow the products of the cooling time, drive up produce efficiency.
注射实现，在保压冷却时，用低温水对模具举行降温料理，以便缩小制品的冷却光阴，抬高出产效率。
This whole needle valve type hot runner injection under low pressure, the injection molding products in contraction deformation is smaller.
针阀整体式热流道在低压下注射使注塑品在收缩时变形更小。
This whole needle valve type hot runner injection under low pressure, the injection molding products in contraction deformation is smaller.
针阀整体式热流道材料浪费少，注塑产品的质量得到改善并更加稳定。
This technique has strong pertinence, good efficiency of removing plug, low cost of materials, which can decrease water injection pressure, increase efficiency of removing plug of oil and water...
该技术针对性强，解堵效果显著，材料成本低廉，能降低注水压力、提高油水井解堵效果，有着良好的应用前景。
So the mechanism study of surfactant flooding in lowering injection pressure and improving oil recovery is significant to the development of low permeability reservoirs.
因此，研究低渗油藏表面活性剂驱降压增注及提高采收率机理及方法，对有效开发低渗油藏、缓解开发中存在的突出问题具有重要的意义。
The results show that: in the ultra-low permeability permeable reservoirs development process, injection pressure increases first and then decreases, at last stays stable;
研究结果表明：特低渗油藏在不同开发方式开发过程中，注入压力都表现为先上升后下降，最后趋于稳定值；
The results show that: in the ultra-low permeability permeable reservoirs development process, injection pressure increases first and then decreases, at last stays stable;
研究结果表明：特低渗油藏在不同开发方式开发过程中，注入压力都表现为先上升后下降，最后趋于稳定值；
应用推荐