Shanghai University has developed a kind of robot, whose control system consists of a master-slave computer system based on the serial communication between VB and microcontroller.
上海大学研制成功的球面机器人控制系统采用了基于VB与单片机的串行通信的两级计算机控制。
The system consists of master module, slave module, communication module, EEG recording module and electrode module.
该系统由主控模块、从控模块、通信模块、信号采集模块和电极几个部分组成。
There are uncertainties in the model of a teleoperation robot system and communication time delays in the communication channels between the master and slave robot.
遥操作机器人系统的通信通道中存在通信时延，而且机器人模型存在不确定性，以致可能造成系统不稳定和操作性能降低。
A mathematical method of tasks assignment for distributed CMC system and the communication protocol of master-slave distributed CNC system etc are also introduced.
同时在文章中还介绍了一种分布式数控系统任务分配的数学方法及主从分布式数控系统的通讯协议等问题。
The protective relaying and fault recorder information processing system is composed of a master station system, communication network and slave station system.
电网继电保护及故障信息管理系统由主站系统、通信网络和子站系统三部分组成。
In distributed measurement and control system with bus structure, master slave communication may be replaced by race communication, when real time and burst are needed.
在总线结构的分布式测控系统中，当系统实时性要求较高、突发性较强时，主从通信方式往往不能适应需要，而需要采用竞争式通信。
In this system the master-slave parallel structure is composed by DSP and PC. The dual machine high speed communication is implemented by the Shared memory.
该系统采用DSP与PC构成主从式并行结构，共享存储器实现双机高速数据通信。
The experimental result shows that it has some useful reference value for the design of serial communication and USB master-slave system.
对于使用串行通信和USB上位机的仪器控制系统设计有一定的参考价值。
In the master -slave multi -computers communication system, slave computer is merely in the position of slave, so it can't initiatively request to communication.
在主从式多机通信中，由于从机完全处于从属地位，因此不能主动请求与主机通信。
At last, the communication program applied in Master-Slave control system base on MODBUS protocol is designed.
最后设计应用于主从式控制系统的通讯程序，这个程序是基于MODBUS协议的。
Finally, in order to consummate the multifunction of the slave, matched software design in the master and establishment of the communication system are related.
最后，为了完善从站的多功能化，本文又对配套的上位机软件设计以及最终通信系统的搭建依次做了论述。
A mathematical method of tasks assignment for distributed CMC system and the communication protocol of master-slave distributed CNC system etc are also intro...
同时在文章中还介绍了一种分布式数控系统任务分配的数学方法及主从分布式数控系统的通讯协议等问题。
A mathematical method of tasks assignment for distributed CMC system and the communication protocol of master-slave distributed CNC system...
同时在文章中还介绍了一种分布式数控系统任务分配的数学方法及主从分布式数控系统的通讯协议等问题。
A mathematical method of tasks assignment for distributed CMC system and the communication protocol of master-slave distributed CNC system...
同时在文章中还介绍了一种分布式数控系统任务分配的数学方法及主从分布式数控系统的通讯协议等问题。
应用推荐