Draw the element for maximum shear stress and mark values of all stresses.
画出最大剪应力的单元体并标出全部应力值。
Maximum shear stress generally takes place at the neutral axis of ship section.
最大剪应力通常发生在剖面的中和轴处。
The straightforward procedures to achieve shear modulus of colloform and maximum shear stress are specified.
提出了求解胶体剪切模量和最大剪应力的简单方法。
The research results show that the maximum shear stress of dual-phase steel raises with the increase of martensite content.
研究表明，随着马氏体含量的增加，双相钢的最大剪切应力随之增加。
Accordingly, the fracture direction is in the direction of the dangerous points where the maximum shear stress action face.
发生塑性剪断时，危险点位于应力场中等效应力取极大值处，断裂方向均为危险点处最大剪应力作用面方向。
It will decrease the maximum axial stress of the lining, but it will increase the maximum shear stress and flexural stress.
开挖引致的松动区减少围岩劲度，将减少衬砌轴向应力，但增加剪应力及挠曲应力。
When the maximum shear stress is greater than the shear strength in the snapped zone of the slope, it will slip and landslide happens.
当最大剪应力的剪切强度大于在快照区的斜坡，它会打滑和山体滑坡发生。
Then the stress distribution of anchored rock mass with partial pull-out failure is analyzed based on the maximum shear stress criterion.
基于最大剪应力破坏准则，分析了局部脱粘破坏锚固体的应力分布。
The results show that the distributing of the maximum principal stress and maximum shear stress are mainly under the control of the landform and fault.
结果显示，隧址区的最大主压应力及最大剪应力分布主要受地形和断层的控制。
The fatigue resistance of the butt welds can be improved by means of removing the weld reinforcement and designing the weld in the maximum shear stress plane.
去除焊缝余高或将焊缝设计在最大剪应力平面内可明显改善对焊接头的疲劳性能。
The calculation indicates that the maximum shear stress around inclusion is 1.2-1.7 times of that without inclusion, which has a harmful effect on the fatigue endurance of rail.
计算发现，夹杂物周围的最大剪切应力是不含夹杂物时的1.2～1.7倍，这对钢轨疲劳寿命造成有害影响。
Around the propagating fault segment the disturbed stress field of maximum shear stress displays an eight petal pattern and that of mean stress displays a four quadrant pattern.
围绕断层扩展部位剪应力增量场呈八瓣式分布，平均应力增量场呈四象限分布。
The further numerical simulation results show that the larger the difference between the two input torques with constant sum, the larger the maximum shear stress of the cylinder.
数值计算结果表明，当输入不相同的阶跃转矩时，负载的最大剪应力水平将显著增加。
The stress accumulation in the southeastern segment of the fault since 1893 has been calculated, and the corresponding contours of maximum shear stress and hydrostatic stress are shown.
计算了1893年以来在断裂带南东段(相对闭锁段)的应力积累，示出相应的最大剪应力和流体静应力等值线图。
The maximum values of shear stress are found in edge of the loaded area on the surface of the upper layer under resultant load.
最大剪应力发生在综合荷载作用下，上层表面荷载边缘处。
With no yielding up to its fracture strength of CFRP, the stress of CFRP at the maximum shear loading is found to be the key parameters in determining shear strength of the columns.
由于碳纤维布无屈服现象，故达到最大荷载时碳纤维布的应力是确定加固后柱受剪承载力的关键参数。
The present method will check maximum anchorage shear stress on the end of shear sheet so as to prevent RC beam from local damage.
采用文中方法可以对钢板端部最大锚固剪应力进行验算，防止混凝土梁出现局部受拉破坏。
Distribution of stress, strain and milling temperature showed that stress is localized in the primary shear zone, while the maximum strain and temperature rise occurs along the tool-chip interface.
应力，应变和铣削温度分布表明，压力是定位在主剪切带，而最大应变和温度升高时沿的刀具芯片接口。
Then take three-dimensional simulation for the model, and analyze the stress distribution when conditions maximum positive shear or maximum nagetive moment happens.
分析在正常使用极限状态下截面内力分别为最大负弯矩和最大正剪力两种工况下应力分布规律。
In this article, it shows formulas to calculate bending moment, shear strength and maximum stress of heat tracing pipe and shell body.
首先给出了半管加热管及壳体的弯距、剪力及最大应力计算公式。
This method can be used to check the maximum bonding shear stress at the end of plate, and to prevent the local destruction of the RC beam.
采用本文方法可以对加强片端部最大锚固剪应力进行验算，防止混凝土梁出现局部受拉破坏。
The maximum tool effective stress is located in the flank face near cutting edge and the shear deformation zone on the workpiece.
最大刀具等效应力出现在前刀面上切削刃的周围，工件上最大等效应力出现在第一变形区。
The results show that the fault has no evident impact on the maximum principal pressure stress but high effect on the maximum principal shear stress;
结果表明：断层对最大主压应力影响不明显，但对最大主拉应力影响较大；
This method can be used to check the maximum bonding shear stress and the maximum peeling normal stress at the end of the GFRP sheet, and to prevent the local bonding failure.
本文公式可用于计算片材端部的最大锚固剪应力和最大剥离正应力，防止局部粘结破坏。
Tightsen structural adhesives have excellent tensile, shear and peel strength combined with maximum impact, stress and vibration resistance.
泰盛结构胶具有较强的拉伸、剪切与剥离强度，耐冲击、耐压、抗振动。
Tightsen structural adhesives have excellent tensile, shear and peel strength combined with maximum impact, stress and vibration resistance.
泰盛结构胶具有较强的拉伸、剪切与剥离强度，耐冲击、耐压、抗振动。
应用推荐