The factors to affect the measuring accuracy are analyzed.
最后分析了影响测试精度的因素。
Furthermore, a high degree of measuring accuracy is ensured.
此外，有高度的测量精度得到保证。
The measuring accuracy of the on-axis component is also discussed in this paper.
本文中还给出了该仪器的系统设计参数并分析了轴向分量的测量精度。
Software calibration method is used to increase measuring accuracy and reliability.
采用软件校正，提高了测量精度和整机的可靠性。
With the new differential pressure method, the measuring accuracy is as high as 2%.
用新式压差法测量蒸发器水位，其测量精度高达2%。
The focus of this paper is how to enhance the measuring accuracy of CNC gear measuring machine.
本文是以如何提高大型数控齿轮测量中心测量精度为目的而展开研究的。
Thus, the measuring accuracy of this method is a little lower than that of the multi-step method.
因此，反向法与多步法相比，测量精确度略低。
These results are from improving instrument quality and increasing instrument measuring accuracy.
并报告了改进仪器质量和提高仪器测量精度的一些实验结果。
Improving measuring accuracy of rate biased laser gyro Angle rate is important to its application field.
提高速率偏频激光陀螺静态角速率测量精度在其应用领域具有重要的作用。
This method increases the measuring accuracy and efficiency greatly about the aerostatic bearing rigidity.
该方法大大地提高了气体静压轴承刚度的测试精度与测试效率。
Its running shows it has high reliability, obtains measuring accuracy demand and realizes complete automation.
实际运行表明：该系统可靠高，达到测试精度要求，并实现完全自动化。
The experiment results show that the method can largely wide the measuring range and enhance the measuring accuracy.
试验表明，该方法扩大了光纤式结冰传感器的测量范围和提高了测量精度。
The processing circuits in the vortex flowmeter are unable to ensure the measuring accuracy in the industrial fields.
涡街流量计中的处理电路不能保证仪表在工业现场的测量精度。
Sets forth all kinds of factors that affect the time parameter measuring accuracy, and proposes fairly reasonable methods.
阐述了影响时间参数测量精度的各种因素，并提出了较合理的方法。
Theequation makes the measuring accuracy of residual stresses with hole-drilling method with cut-ting tools improved greatly.
本关系的获得使得采用刃具钻孔测量残余应力的精度有很大提高。
The design can be used to test the required testing items of present protective devices and its measuring accuracy is enough.
此设计能对目前继电保护装置所要求的项目进行测试和试验，并满足了要求的精度。
The results show that the system has high measuring accuracy, high applicability at the site and relatively higher practical value.
结果表明，该系统测量精度高，现场适应性强，具有较高的使用价值。
The influence of various parameters on the measuring accuracy of the convective heat-transfer coefficient was analyzed quantitatively.
本文全面分析了各因素对对流换热系数精度的影响，并进行了定量分析。
Since the ultimate measuring accuracy is limited by the accuracy of calibration, a new method of calibration is proposed in this paper.
由于测量的精度最终要受到标定精度的限制，本文引入了一种新的标定方法。
The system has high measuring accuracy, fast machining speed and better automaticity, becoming the quality assurance of work machining.
这些系统测量精度高、速度快、自动化性能强，成为工件加工的质量保证。
The instrument introduced in the magnetostrictive technology has high measuring accuracy, low cost, long life and easy installation etc.
该仪表采用磁致伸缩技术，具有测量精度高、成本低、寿命长和安装简便等特点。
This paper analyse the influences of precision of bridge, measuring jig and so on to measuring accuracy, and discusses the improvements.
本文分析了电桥的精度、测量夹具等因素对测量结果准确性的影响，并提出了具体改进措施。
This is an effective approach to improving the sensitivity and measuring accuracy under the same condition for the Michelson interferometer.
这是使迈克尔逊干涉仪在同样条件下提高灵敏度及测量精度的一条途径。
In order to increase the measuring accuracy the sample averaging method must be introduced, so that a certain time of measurement is needed.
为了提高测量精确度，减少随机误差，对噪声峰值测量应采用统计平均方法，所以也需要一定的测量时间。
The error sources affecting measuring accuracy of the system were analysed in detail and the way to improve accuracy of the system was given.
详细分析了影响系统精度的误差来源指出进一步提高精度的措施。
The circuit and method for obtaining equal measuring accuracy and response speed in a wider frequency signal range are discussed in this paper.
本文探求在较大的被测频率信号范围内获得相同的测量精度与响应速度的测量方法及电路。
The measuring instrument can improve the measuring accuracy of water content, and realizes continuous measurement of water content in oil well.
研制的仪器不但提高了测量精度，还实现了油井含水率以往难实现的连续测量。
It is illustrated how to reasonably select measurement reference for complex parts in order to improve measuring accuracy and lower measuring error.
阐述了一些复杂零件如何合理选择测量基准，以提高零件的测量精度，减小检测误差。
It is illustrated how to reasonably select measurement reference for complex parts in order to improve measuring accuracy and lower measuring error.
阐述了一些复杂零件如何合理选择测量基准，以提高零件的测量精度，减小检测误差。
应用推荐