As samples, the distributions of ice sheet design thickness, compressive strength, flexural strength, shear strength and elastic modulus for ice periods of 25, 50 and 100 years are presented.
作为实例，给出渤海25、50、100年重现期的平整冰层设计厚度分布、压缩强度分布、弯曲强度分布、剪切强度分布和弹性模量分布。
A new experiment of measuring modulus of elasticity with the flexural method on the experiment device of CSY sensor system is introduced.
本文介绍在CSY型传感器系统实验仪上扩展用弯曲法测材料弹性模量新实验。
Experimental results show that the flexural modulus increases with the increases of the fibre content and length.
实验表明，随着纤维含有量和纤维长度的增加，材料弯曲模量呈递增趋势。
Alkaline treatment of wood flour makes flexural strength and flexural modulus of the composite decrease by 20.
木粉的碱化处理使复合材料的弯曲强度和弯曲模量分别下降20。
Based on the testing results, ultimate flexural strength and flexural Young's modulus have been studied.
根据试验获得的结果，综合地分析了其极限弯拉强度和弯拉弹性模量；
The results also show that the density has a great impact on the strength and modulus rather than the flexural deflection.
材料密度对弯曲强度和模量影响很大，但对弯曲挠度基本没有影响。
Compressive strength, splitting strength, flexural strength, compressive resilience modulus and flexural resilience modulus of cement stabilized stone of different structure types were tested.
并对不同结构类型水泥稳定碎石材料的抗压强度、劈裂强度、抗折强度、抗压回弹模量以及抗折回弹模量进行了试验研究。
The results showed that the tensile strength, flexural strength and flexural modulus increased obviously with increase of amount of Mica.
结果表明，复合材料的拉伸强度、曲强度和弯曲模量随着云母用量的增加而提高。
The influence of hygrothermal environment on flexural strength of composites is greater than flexural modulus.
湿热对复合材料弯曲强度的影响要大于对弯曲模量的影响。
Fabric Stiffness Tester. To determine the bending height, flexural rigidity and bending modulus of fabric by simple procedures and calculation.
织物硬挺度测试仪，可通过简单操作及计算测出织物的弯曲高度、弯曲刚度、弯曲模量。
The flexural strength and flexural modulus decreased with the increasing amount of ABS.
合金的弯曲强度和弯曲模量都随着合金中abs用量的升高而下降。
Flexural strength and modulus of super-hybrid composite can be improved greatly by the better interfacial control. And the increasing rate of flexural modulus is more than that of flexural strength.
通过良好的界面控制，可显著提高复合材料的弯曲强度和弯曲模量，模量的提高比强度的提高幅度更大。
With the increase in ha content, the flexural strength and flexure modulus of composites had been greatly increased and the tensile strength of composites had only a little change.
随着复合材料中ha含量的增加，材料的弯曲强度、弯曲模量有大幅提高，而材料的抗拉强度即韧性降低不大。
It shows that after adding 20% low profile additive to the UP resin, the shrinkage rate of cured resin is 2.1%, the retention rate of bending strength is 88% and no change in flexural modulus.
结果表明，在不饱和聚酯树脂中加入2 0 %的该类低收缩添加剂，树脂的固化收缩率为2 1% ，弯曲强度保有率为88% ，弯由模量没有明显变化；
Results showed that as the hardness of modified EPDM increased the brittle-ductile transition moved to high rubber contents and the flexural modulus increased profoundly, however.
结果表明：随着EPDM硬度的增加，共混物不仅韧性提高，弯曲模量也大幅度上升。
Mechanical tests show that the(Young's) modulus, microhardness, flexural strength and compressive strength of the carbons are higher than those of traditional carbon materials.
各向同性热解炭与传统炭材料相比具有较高的杨氏模量、硬度和强度。
The flexural strength, first crack strength, modulus of elasticity and flexural toughness of high-strength lightweight fiber-reinforced concrete were investigated.
对轻骨料高强度钢纤维混凝土的抗压强度、初裂强度、弯曲强度、弹性模量和弯曲韧性指数等主要力学指标进行了试验研究。
The anti- presses the modulus of resilience lower and can reduce the flexural-tensile stress of the material bottom.
抗压回弹模量降低可减少材料底部的弯拉应力。
The addition of OMMT improved the tensile strength, flexural strength and flexural modulus of the alloy, however, the impact strength decreased to a certain extent.
结果表明，OM MT的添加可以提高体系的拉伸强度、弯曲强度和弯曲模量，但冲击强度会有某种程度的下降；
The results show that the addition of mica can enhance the flexural strength, flexural modulus, notched Izod impact strength and heat deformation temperature of the composites;
结果表明：云母可有效提高PP的弯曲强度及模量、悬臂梁缺口冲击强度和耐热性能；
The result showed that impact strength of the blending system increased, while tensile strength, flexural strength and flexural modulus decreased with the addition of impact modifier ACR;
酯交换抑制剂的加入，降低了共混体系的力学性能，适当的酯交换反应有利于共混体系力学性能的提高；
The result showed that impact strength of the blending system increased, while tensile strength, flexural strength and flexural modulus decreased with the addition of impact modifier ACR;
酯交换抑制剂的加入，降低了共混体系的力学性能，适当的酯交换反应有利于共混体系力学性能的提高；
应用推荐