With this evaporative cooling approach, the mold temperature is automatically evened out.
与此蒸发冷却的方法，具温度是自动，最终列。
This series of products are mainly used to control automatically plastics mold temperature.
该系列产品主要用于塑料模具的自动恒温控制。
Proper decrease in pouring temperature and increase in shell mold temperature are helpful to preventing hot tear.
为避免产生热裂应适当降低浇注温度，提高型壳温度。
Our results show that mechanical properties of PP samples strongly depend on the melt temperature and mold temperature.
实验结果表明，熔体温度和模具温度对试样的力学性能有重要影响。
JTH series water type mold temperature control machine is mainly applied to the mould heating and constant temperature.
JTH系列水式模具控温机主要应用于模具的加热与恒温。
JTL series water type mold temperature control machine is mainly applied to the mould heating and constant temperature.
JTL系列水式模具控温机主要应用于模具的加热与恒温。
The mold temperature obviously influences the molding process, while the melt temperature influences comparatively less.
模具温度对成型过程的影响较大，熔体温度的影响相对较小。
The mold temperature is controlled effectively by controlling the flow of the external coolant through the heat exchanger.
具温度是有效的控制，通过控制流通的外部冷却水通过换热器。
The higher the pouring temperature and initial mold temperature are, the larger the plastic strain while the smaller the thermal stress is.
浇注温度和砂型初始温度越高，热节处粘塑性应变越大，而热应力越小。
Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times.
加工窗口分析、它零件的模流分析，检查熔体温度、具温度、塑压力和充填时间。
The static and dynamic mechanical properties have been studied for PP that have been injected at different melt temperature and mold temperature.
本文研究了在不同的熔体温度和模具温度下，注射成型的聚丙烯塑料试样的静态和动态力学性能；
By using metal mold casting, we can control mold temperature, infusing temperature, infusing speed to avoid defects of pore, cold partition, shrink and loose.
采用金属型立式浇铸，严格控制铸造工艺参数(模具温度、浇注温度、浇注速度)，以避免气孔、缩松、冷隔等缺陷的产生。
By use of orthogonal test design, how the injection speed, pouring temperature and mold temperature effects the casting shrinkage porosity forming is studied.
然后，本文通过正交试验的方法研究了压射速度、浇注温度和模具预热温度对铸件缩松缩孔缺陷的影响。
At proper pouring temperature and mold temperature, the effect of die casting speed and pressure on microstructure and properties of AM60B alloy has been studied.
固定浇注温度和铸型温度，研究压射速度和压射比压对压铸am 60 B合金组织与性能的影响。
First preset mold temperature machine to the temperature required for injection mold, molding for the high-quality products once and reducing the tryout material.
模温机先预调达到注塑模具所需的温度，一次成型为优质产品，减少试模原料。
Effects of different cooling rates and uneven mold temperature on the residual stress inside injection molded parts are studied with the help of numerical methods.
采用数值方法研究了不同冷却速率、不均匀模壁温度对塑件残余应力的影响。
The control of mold temperature in injecting process has extraordinary important influences not only on the quality of the injected products but also on the process itself.
注塑模具的温度控制对注塑工艺和注塑件的质量有非常重要的影响。
The results show that adopting a good cooling channel project, the mold temperature can be controlled in a reasonable range and the thermal stress of the mold can be reduced greatly.
研究表明：良好的冷却方式可以做到将模具温度很好地控制在合理的范围内，且模具产生的热应力也可以大大降低。
Die from the back of high temperature water through the pipe back to mold temperature machine, the pump pressure delivered to the heater, the heating tube is sent to die, so the cycle.
从模具囬来的高温水经过管路囬到模温机，经泵浦加压后输送到加热器，通过电热管加热送至模具，如此循环。
The result of experiment shows that, at constant value of other factors, the changes of pouring and mold temperature have greater effects on microstructure and properties of AM60B alloy;
实验结果表明：在其他工艺参数一定时，浇注温度、铸型温度变化对压铸镁合金AM60B组织与性能有较大的影响；
The results show that mold temperature is the most significant influence factor, injection speed takes the second place, and pouring temperature is the least significant influence factor.
研究表明：模具预热温度影响最大，压射速度次之，浇注温度影响最小。
Analyzed the influence of the plastic part injection molding process to part quality, introduced design of injection mold, mold parting structure design and mold temperature control design.
分析了塑件的成型工艺及模具注射成型对塑件质量的影响，介绍了浇注系统的设计，模具分型结构、模温控制的设计。
The invention discloses casting equipment and a casting method using solid-liquid two-phase region temperature as casting mold temperature, and belongs to the technical field of metal casting.
一种铸型温度为固液两相区温度的铸造设备与方法，属于金属铸造技术领域。
As long as the pre-set current value and a good bonding time, the system based on current feedback signal auto - Regulation, will not be glued current thickness change and mold temperature rise.
只要预先设定好胶合电流值和时间，本系统会根据电流的反馈信号自动调节，胶合电流不会受到厚薄的变化和模具温度上升的影响。
New-designed XB series of industrial chillers are capable of controlling precisely the mold temperature in plastic molding process as so to shorten molding cycle and speed product formalization.
全新造型的XB系列工业冷水机主要适用于塑胶工业，它可以精确的控制塑胶成形模具温度以缩短成型周期，加速产品定形；
In this paper the effects of pouring temperature, mold temperature, inoculants, and section size on the microstructure and mechanical properties of casting nickel-base superalloy K24 were studied.
本文研究了浇铸温度、铸型温度、孕育剂和截面尺寸对K 24镍基铸造高温合金的组织和性能的影响。
In this paper the effects of pouring temperature, mold temperature, inoculants, and section size on the microstructure and mechanical properties of casting nickel-base superalloy K24 were studied.
本文研究了浇铸温度、铸型温度、孕育剂和截面尺寸对K 24镍基铸造高温合金的组织和性能的影响。
应用推荐