At present, the phenomenon of axial desquamation for an individual ejector pin plate or an annular cutter can occurs in a disposable digestive tract anastomat component.
目前，一次性使用的消化道吻合器组件，会发生个别推钉片或环形切刀轴向脱落的现象。
Two commonly used treatment methods are external fixation combined with percutaneous pin fixation and plate fixation.
常见的两种方法是经皮穿针外固定术和钢板内固定术。
The Style X body design has special geometry and plate configuration to allow each plate to strike the stop pin in its center of percussion.
类型阀体结构具有特殊的几何结构和阀瓣配置，使得每个阀瓣撞击在其撞击中心的止动销上。
In the design illustrated, the core pin is anchored by a local core-retaining plate.
图示的设计中，型芯杆是用一个局部的型芯挡板固定的。
The plate was loaded in its own plane by a pin passing through the hole in an annular disc fitted in the hole in the plate.
平板的孔里面镶嵌著一个套环，在此圆盘的孔中穿过一个销钉而使平板在其自身平面内受载。
The plate was loaded in its own plane by a pin passing through the hole in an annular disc fitted in the hole in the plate .
平板的孔里面镶嵌著一个套环，在此圆盘的孔中穿过一个销钉而使平板在其自身平面内受载。
Heat punching process of pin axle hole of chain plate with high strength, big thickness and long circumference was introduced, and a few attention issues of heat punching process were given.
介绍了强度高、厚度大和周边长的链板销轴孔的热冲裁加工以及链板热冲裁加工中的几个问题。
It is important for the beginner to note that the core pin extend completely through the sleeve, and is attached to the back plate.
对于初学者来说重要的是注意型芯延伸完全穿过顶管，并且安装在底板上。
Complications included pin loosening in 24, pin infection in 4, loss of the reduction in 4, penetration of inner plate of calvaria in 3 and pressure sores in 1 case.
并发症包括颅钉松动（24例）、钉孔感染（4例）、复位丢失（4例）、颅钉穿透颅骨内板（3例）、背心下皮肤压疮（1例）。
Heat blanking process of pin axle hole of chain plate with high strength, large thickness and long circumference was introduced, and a few problems of heat blanking process were presented.
介绍强度高、厚度大、周边长的链板销轴孔的热冲裁加工以及链板热冲裁加工中的几个问题。
Results: Seventy-four (51%) of the fractures were treated with external fixation and percutaneous pin fixation, and seventy were treated with dorsal, volar, or combined plate fixation.
结果：74处(51%)骨折采用经皮穿针外固定术，其余70处采用背侧、掌侧或双侧钢板内固定术。
Move the valve plate moves from the valve plate cross walk tissue valve plate lower sprocket drive transmission pin to honor.
阀板横挪动作由阀板行走组织的链轮驱动阀板下部的传动销轴来兑现。
Position drive plate on the crankshaft's dowel pin and press on to the crankshaft flange.
将传动盘安放在曲轴的定位销上，然后压到曲轴法兰上。
First of all, within the target-oriented in the plate and guide pin sets, and then slide the sleeve nut plate.
首先在垫板内对准导向销和导向套，然后滑入防松套筒板。
The pin screw fits in the center hole of the camera plate.
别针螺丝适合照相机板材的中心孔。
Play great positioning pin ensures disc not because butterfly plate gravity drop, also can be installed in the valve stem end adjustment block to ensure that the butterfly plate fixed position.
弹赞定位销可保证蝶板不会因为蝶板重力作用下坠，还可在下阀杆端部设置调整块来保证蝶板位置固定。
The invention relates to a grain harrow, comprising a harrow handle (1), a torsion spring (5), a push plate (6) and a harrow pin (7);
本发明是一种谷耙，包含有耙柄（1）、扭簧（5）、推板（6）和耙钉（7）；
The lifting plate is locked automatically by a positioning pin, and then the supporting plate of the pancake is replaced to enable the pancake machine to automatically work again.
定位销自动锁住升降板，然后更换煎饼托板，煎饼机重新自动开始工作。
The pin gear-type precision seeder is composed of a wheel body, a rubber ring, a needle wheel and an isolation plate.
本实用新型主要由轮体、胶圈、针轮、隔种板等构成。
The connection type between the vertical guide plate of the vertical adjusting mechanism and the positioning plate can adopt compression-fitting connection or dowel pin type connection.
纵向调节机构的纵向导板与定位板之间的连接方式可采用压紧连接或柱销式连接。
I produced, the step-up circuit board by DuPont with the following pin connected to the main circuit plate board (Figure 6), this way you can take your own, as long as easy to produce on the line.
我公司生产，商场电路板由杜邦公司以下列销钉连接到主电路板板(图6)，这样你就可以把你自己，只要容易产生危险。
The effects of additional friction between pin and pin-hole and of the height of pin over the press-plate surface on the practically measured values was taken into account and their corrections were …
在计算中，考虑了测针与针孔壁间的附加摩擦力，以及测针端部凸出压板表面的高度对实测结果的影响，并分别进行了修正。
The methods and the program can be used to guide the choice of milling cutter when processing the inner curve of pin gear housing in double crack three ring-plate cycloid reducer.
本文介绍的方法和编制的软件可用于指导现场中环板针齿壳内曲线加工铣刀的选取。
Pin the s America Plate at the tip, but spread the Atlantic apart so the top part of s America must roll to the west.
南美板块被钉在了顶端，但大西洋要扩展开来，因而南美板块的顶部一定会滚动到西面。
Standard installation methods: screw thread, plate or pin plunge, etc.
标准安装制式：螺纹、平板、插杆等等。
Standard installation methods: screw thread, plate or pin plunge, etc.
标准安装制式：螺纹、平板、插杆等等。
应用推荐