The 14-cylinder engine turns the longest propeller shaft (130 metres) ever built, at the end of which is the largest propeller, weighing in at 130 tonnes.
14缸发动机转动最长的推进器杆(130米)，在其末端是最大的推进器，重130吨。
This avoids the use of a traditional propeller shaft and puts the propellers in a clear flow of water, which greatly improves efficiency.
这样就避免了使用传统的螺旋轴，将螺旋桨置于干净的水流中，从而大大提高了效率。
These drive the central propeller shaft through bevel reduction gears with a 2:1 reduction.
这些驱动器，中央螺旋桨轴通过减少锥齿轮2：1减少。
Aligning intermediate shaft and propeller shaft after launching.
下水后中间轴和螺旋桨连接后校中。
Check for surface contact area (metallic contact) between stern shaft and propeller hub tapers.
检查螺旋桨轴与螺旋桨锥度接触面。
Please bond the propeller to shaft.
请进行螺旋桨胶合连接。
Tiny deformation will appear in the local of the propeller shaft of certain ship which is endured an invariableness load, although the shaft stress is within the elastic limit range.
某舰的螺旋桨尾轴长期处在恒定载荷作用下，虽然尾轴应力在弹性极限范围内，但是尾轴局部还是很容易发生微量的塑性变形。
When the power required by propeller is so high that the shaft speed cann't arrive a rated value, the tip of propeller can be cut to decrease its load.
当螺旋桨要求的功率过高以至于轴转速达不到额定值时，可以采用切割螺旋桨叶梢的方法减小螺旋桨的负荷。
Align the installation reference marks on the propeller shaft and yoke and install the propeller shaft.
对准传动轴和轭上安装参考标记，安装传递轴。
So it is significative to carry out a research on room temperature creep characteristic of propeller shaft .
所以对螺旋桨尾轴进行蠕变分析是十分有意义的。
Inspection machining dimension of propeller shaft (intermediate shaft or counter shaft).
螺旋桨轴(中间轴)机加工尺寸检查。
This measurement will give you the propeller shaft Angle (C).
测量结果就是传动轴工作角(c)。
The propeller is to be force fitted to the propeller shaft by using the hydraulic jack which the Builder possess and secured by wet type keyless fitting method.
螺旋桨通过使用船厂提供的液压顶升装置压入螺旋桨轴并采用湿式无键固定法紧固。
Different propeller has different shaft frequency.
目标的螺旋桨不同则轴频不相同。
All Marine engines could be sold with gearbox, and some engines could be sold with tail shaft and propeller.
全系列产品均可以匹配齿轮箱销售，部分机型可以连带尾轴，螺旋桨销售。
The propeller shaft frequency is one of the important target recognition features for passive sonar.
螺旋桨轴频是被动声纳极其重要的目标识别特征之一。
BMW Corporation of West Germany has developed a torsion rig for universal joint propeller shaft and axle shaft for the use of testing four-wheel-drive cars.
联邦德国的BMW公司开发了一种万向节传动轴与半轴的扭转试验台，专供四轮驱动型桥车试验用。
In this step, work to drill for the pipe of a propeller shaft or a rudder.
在这个步骤中，演练工作，为管道的传动轴或舵。
In this paper the author emphasizes the importance of balancing the rotating parts, such as crankshaft, flywheel, propeller shaft, wheel and tyre, etc. during automobile repair.
分析了汽车维修中曲轴、飞轮、传动轴、车轮、轮胎等旋转零件进行平衡试验的重要性。
The propeller on the propeller shaft is located outside the rudder propeller housing.
螺旋桨轴上的螺旋桨位于所述舵桨壳体的外部。
Starting from analyzing the structural properties of the Marine propeller shaft bracket, the authors introduce the technology calculation, design, process and their production experience.
从分析船舶尾轴架结构特点入手，介绍尾轴架工艺计算、工艺编制、产品生产过程及经验。
For connecting the output shaft of the gear box to the rear axle, a ling shaft known as propeller shaft is used.
为把齿轮盒子的输出桥连结到后面的轮轴，鳕即是螺旋桨桥的桥被用。
This accommodates any effective change of length of the propeller shaft as the rear axles move toward or away from the CAR frame.
当后桥在车架上向前或向上运动时，这种结构足以调整传动轴长度的任何变化。
There must be one or more universal joints to permit variations in the Angle of drive. there must also be a slip joint that permits the effective length of the propeller shaft to change.
一个或几个万向节来适应传动角度的变化；一套伸缩花键，能够改变传动轴的现有长度。
The reason the propeller shaft shortens as the Angle increases is that the rear axle and differential move in a shorter ARC than the propeller shaft.
当角度增加时，传动轴变短的原因是后桥和差速器运动的弧度小于传动轴运动的弧度。
Rotary motion of the transmission main shaft carries through the propeller shaft to the differential, causing the rear wheels to rotate.
变速器主轴的旋转运动通过传动轴传递到差速器上，使后车轮转动。
Rotary motion of the transmission main shaft carries through the propeller shaft to the differential, causing the rear wheels to rotate.
变速器主轴的旋转运动通过传动轴传递到差速器上，使后车轮转动。
应用推荐