Low energy consumption, high output and big reduction ratio;
能量消耗小、产量高、破碎比大。
The reduction ratio declined slowly and was relatively stable.
缩减比例逐年小幅降低，相对稳定。
The maximum NOx reduction ratio of CWS obtained in this study was 64%.
试验获得的最高水煤浆脱硝率为64%。
High molecular weight. Low reduction ratio. Excellent thermal stability. .
高分子量。低减速比。优良的热稳定性。
Lung-mediation reduction ratio of air type indicate squamous cancer strongly.
含气型肺、纵隔窗缩减率高度提示肺腺癌。
The experiment results, show that the range of reduction ratio is very practicable.
理论计算结果与实验结果对比表明，所得减薄率选取范围具有较强的实用性。
The influence of magnitude of the reduction ratio on the products quality was studied.
并对钼方坯旋锻归圆前道次压缩比的大小对钼产品质量的影响进行了研究。
In this paper, the method measuring joint reduction ratio of V01 arc welding robot is presented.
提出了V01弧焊机器人关节减速比的测量方法。
With the increase of reduction ratio, the volume fraction of dynamic recrystallization increases.
随着压下率的增加，动态再结晶体积分数升高；
REDUCTION RATIO BY VOLUME: Use clean water, 10 parts of paint to 1parts of water. Stir well before use.
稀释份量：根据施工需要，可酌情用0-10％的自来水稀释，充分搅匀后使用。
The rational gap length reduced the volume of adhesive effectively and the highest reduction ratio was 60%.
合理的间隙长度可以有效地减少胶粘剂的用量，减少率最大可达60%；
The stress reduction ratio and the vertical stress distribution in the embankment fill were studied in detail.
根据试验结果，分析了应力折减系数大小和填土中的竖向应力分布特点。
Especially it is suitable for being used in all kinds of equipments required high power and big reduction ratio.
因此，这种传动装置特别适合应用于各种需要大减速比和传递大功率的装备之中。
General-purpose resin. Medium reduction ratio. Excellent color and clarity. Accepts filler exceptionally well. .
通用树脂。中等缩小比例。出色的色彩和清晰度。接受填料出色。
The speed is based on the synchronous motor speed reduction ratio as a benchmark calculated by dividing the value of.
转速是以电动机的同步转速为基准除以减速比而算出的数值。
When the cumulative reduction ratio reaches 30%, about 67% of the inner region of the axial forging is modified fully.
当压下率达到约30%时，随材料心部有67%的区域充分改性；
These factors include ratio of upper and lower roll diameter , reduction ratio , enterance angle and roll rotation speed.
因素有上下轧辊直径比、压下率、导入角和轧辊转速。
In determining the main reduction ratio, the drive axle of the mechanical and structural analysis, and calculated the school.
在确定了主减速比之后，通过对驱动桥的力学和结构分析，进行计算校和。
The attribute reduction quality, which includes reduction ratio and approximate quality, is defined to scale the reduction effectiveness.
提出约简质量的定义，从属性约简率和近似质量两方面来衡量约简效果。
Multi-purpose mini-motorcycle in the belt drive gear for the latter, the main, the size of the driven pulley reduction ratio sub-decision.
在微型摩托车多用皮带传动方式作后传动装置，主、从动皮带轮的大小决定次级减速比。
Tolerance of wheat varieties to insect injury was determined with ratio of aphid numbers and reduction ratio of wheat weight per 1000 grains.
用蚜量比值和千粒重降低比值法测定了小麦品种的耐害性。
The primary drive gear(crankshaft gear)and the primary driven gear are the source of noise due to their high speed and bigger reduction ratio.
作为摩托车初级传动的曲轴齿轮及初级从动齿轮，由于转速高及降速比大，是产生噪声的主要因素。
Premium resin offers highest thermal stability, stress crack resistance, flex life, and clarity of all grades. Low to medium reduction ratio. .
高级树脂提供了最高的热稳定性，耐应力开裂，弯曲的生活，和所有级别的清晰度。低到中等缩小比例。
Through the comparison of numerical simulation value and experiment results, the range of reduction ratio was obtained while the tube forming ideality.
通过数值模拟与实验结果的比较，得出了获得较理想的成形薄壁筒形件时减薄率的选取范围。
The influences of strip thickness, forward and backward tension, reduction ratio and resistance to deformation on the edge drop were investigated in detail.
详细研究了带钢厚度、张力、压下率、变形抗力等对边缘降的影响。
Steelmaking Plant of WlSCO, the main technological parameters were analyzed and optimized, such as reduction position, reduction amount, and reduction ratio.
结合武钢二炼钢动态轻压下技术的应用情况，对压下位置、压下量、压下率等主要参数进行了分析及优化。
After the model is decided, choose power, reduction ratio and assembling type in accordance with the conveying capacity, conveying distance and layout (see Table 5-12).
选定机型后，可根据输送量，输送长度和工艺布置状况(参照表5 - 12)选择动力和减速机速比及装配型式。
Planetary reducer motor with small size, light weight, wide range of reduction ratio, high transmission power, smooth running, compact structure, high bearing capacity.
行星减速电机具有体积小、重量轻、减速比范围广、传动功率高、运转平稳、结构紧凑、承载能力高等优点。
Experiments show that this approach can achieve high energy reduction ratio by exploiting the dynamic slack time sufficiently and controlling the scaling overheads effectively.
实验结果表明，该方法能够充分利用动态松弛时间，有效控制调整开销，实现较高的能耗优化率。
The method used to determine volume-reduction ratio for scroll compressor with modified profile is proposed. Formula for compression pockets and volume-reduction ration are given.
提出了一种修正型线涡旋压缩机内容积比的确定方法，给出了压缩腔容积和内容积比计算公式。
应用推荐