The gap in the top ring groove had exceeded the requirement.
第一道环槽的天地间隙超过了请求。
The laser heat treatment process and mechanism on the surface of piston ring groove were studied.
对活塞环槽表面的激光热处理工艺与机理进行了试验研究。
The piston rings carried in the ring groove are of two basic types: compression rings and oil-control ring.
安装在环槽中的活塞环有两种类型：压缩环和机油环。
Application of argon arc local strengthen can increase hardness and high-temperature wear resistance of the ring groove.
采用氩弧局部强化可提高环槽的硬度和高温耐磨性。
Two groove of the inner ring and outer ring groove for the ball between the form of a drum, equipped with roller bearings.
二条滚道的内圈和滚道为球面的外圈之间，装配有鼓形滚子的轴承。
The ceramic treatment for the first ring groove of ZL108aluminum alloy piston was conducted with micro-arc oxidation technique.
利用微弧氧化技术对ZL 108铝合金活塞第一道环槽进行了陶瓷化处理。
The periphery of the male buckle is provided with an installing ring groove, and one end of the male buckle is provided with the bulge.
它由公扣和母扣组成，公扣的外周设有安装环槽，公扣的一端设有凸出部；
The testing results show that these VCSELs operate with good performance, light output power is 1.34 times as much as that with ring groove.
测试结果表明这种新结构器件不仅表现了良好的工作特性，而且输出功率也提高到环形沟槽结构的1.34倍。
Upper and lower piston rings are arranged inside a piston gaseous ring groove, and openings on the two-piece piston rings are mutually staggered.
在一个活塞气环槽内设有上下二片活塞环，二片活塞环上的开口相互错开。
Outer ring groove of curvature of the center and bearing center consistent, so with automatic self-aligning ball bearing the same tone heart function.
外圈滚道面的曲率中心与轴承中心一致，所以具有与自动调心球轴承同样的调心功能。
With cars, milling, boring, drilling four automation function, can be turning sphere, cylinder, cone, thread, tapping, end face, inner and outer ring groove, etc.
具有车、铣、镗、钻四大自动化功能，可车削球面、柱面、锥面、螺纹、攻丝、端面、内外环槽等。
Time for the third kind of closing well is so long that flange steel ring groove on the top of casing-head is heavily corroded in M4 well being situated in Tarim basin.
位于塔里木盆地的M4井，由于三类封井时间较长，造成套管头上部法兰钢圈槽严重腐蚀。
The dimensions of the snap ring groove and of the chamfer adjacent to the groove (fig 20) are in accordance with ISO 464:1995, which also specifies suitable snap ring dimensions.
止动槽和紧邻的倒角（图20）尺寸符合1995年的ISO464标准，该标准还规定了适当的止动环尺寸。
The insulating rubber sealing layer is stuck on the surface of the unidirectional weftless tape banding layer for the commutator. The ring groove is arranged at the end of the commutator plate.
所述的换向器在无纬带绑扎层表面粘接有绝缘胶泥密封层，在换向片端部有一环状沟槽。
Out in the shaft loaded oil ring groove or by centrifugal force along the axis of the oil drain off the surface, the oil flows back to the assembly after the pool, and thus play a role in sealing.
在轴上开出沟槽或装上油环，借离心力将沿轴表面外流的油甩掉，集结后流回油池，因而起到密封的作用。
In some application, a narrow groove is cut into the piston above the top ring to serve as a "heat dam" to reduce the amount of heat reaching the top ring.
在一些实际结构中，一条窄槽切入顶端活塞环的上部，其作用是充当“隔热槽”以减少达到顶端活塞环的热量。
Deep Groove ball bearings are the most popular of all the ball bearing types because they are available in a wide variety of seal, shield and snap-ring arrangements.
深沟球轴承是所有类型的球轴承最流行的，因为他们是在一个密封，盾牌和管理各种各样的戒指安排可用。
Snap ring used to maintain the groove.
用以保持止动环的槽。
In order not to make nickel ring up tank, outside groove diameter ratio inside groove is big, this on the structure solved the nickel ring grooving problem.
为了不使镍环起槽，外沟直径比内沟大，这在结构上解决了镍环起槽问题。
A screwdriver is used to remove the spiral seat retainer ring from its groove.
采用一把螺丝刀从凹槽中拆卸螺旋阀座定位器环。
Shaft snap ring in groove on shaft.
将轴承及护脂毡圈紧靠在卡环上。
The inside surface of the ring fits in the groove on the piston.
些环的内表面和活塞上的凹槽相配合。
Insert ball bearings are designed in almost the same way as deep groove ball bearings, except the outer ring is spherical and with wide inner rings.
内嵌的球面轴承除了球面型的外圈和超长的内圈外，其他的设计结构与深沟球轴承很相似。
There is a snap groove in the outer ring for fitting a snap ring, so it is convenient to assemble the bearing.
轴承外圈上设有止动槽，以便装上止动圈，因此轴承的安装较方便。
With clear acrylic housings you can visually check that the 'o' ring is seated correctly in the groove by looking through the side of the housing BEFORE entering the water.
现在的树脂外壳，可以让你非常方便在下水前观察O型圈是否就位妥当。
We analyse the influence of the elastic deformation and the surface roughness for lubricating characteristics and give a thought of cutting groove in piston ring.
分析了弹性变形、表面粗糙度对润滑性能的影响，并提出了开槽环的设想。
And the structure of the soft sealing ring of this product is pressed by a metal ring set in the seat within a groove on the ladder which can't drop and be convenient to change.
而且此产品的软密封结构的密封圈是由金属圈压套在阀座上的阶梯凹槽内，具有密封不脱落，而且可以很方便的更换等优点。
The system design variables are magnet external diameter of internal ring, internal diameter of external ring, depth of groove - ring and ampere turns.
系统设计变数为磁铁内环外径、外环内径、槽口深度和安匝数。
The system design variables are magnet external diameter of internal ring, internal diameter of external ring, depth of groove - ring and ampere turns.
系统设计变数为磁铁内环外径、外环内径、槽口深度和安匝数。
应用推荐