The sensor shall be mounted on object surface, by fixation of screw thread or flange, and ensure firm contact with the equipment surface.
传感器采用贴面形式安装在物体表面，固定形式为螺纹或法兰，并确保与设备表面接触严密。
The response surface methodology was used to study the influences of screw speed, barrel temperature, material moisture and enzyme mass fraction on DE values.
采用响应面分析方法研究了螺杆转速、机筒温度、物料水分和酶质量分数对挤出物de值的影响规律。
The BP neural network used in the temperature characteristic of the boundary film on the screw-nut pairs surface in the wear-self-compensation system was established.
本文用双隐层BP人工神经网络建立了丝杆螺母副表面边界膜温度特性的磨损自补偿数学模型。
It is found that outcrops of micropipes on the crystal surface possess remarkable feature of double or multiple screw dislocations.
利用光学显微术观察了原生晶体的表面形貌，发现了微管在晶体表面的露头点具有明显的多个螺位错成核特征。
The varying pitch helixes were constructed on the parameter equation, and were selected as sweep trajectory; the surface of the screw was enveloped on the generating method.
设计过程中按推导出的数学方程构造各段螺旋线，并以该螺旋线作为扫描轨迹，遵循范成法原理包络出螺杆的各段螺旋曲面。
The image force acting on the piezoelectric screw dislocation and the generalized stress on the surface of rigid line are calculated.
导出了作用在位错上的像力和刚性线夹杂表面剪应力和电位移的解析表达式。
User requirements and in accordance with the surface coating on the screw has been worn carbide and restoration of the old screw.
并可根据用户要求对螺杆表面喷涂硬质合金和对已磨损的旧螺杆修复工作。
The surface temperatures of grooves of an oil-flooded single screw compressor are measured with a slide-ring, and the surface temperatures on different working conditions arc given.
利用滑环装置测量了喷油单螺杆压缩机转子螺槽的表面温度，给出了各种不同工况下表面温度的数据。
The positive pressure distribution on the bearing surface of screw down system of 950 primary mill was studied using FEM and the corresponding improvement way has been put forward.
通过有限元分析，研究了950开坯机压下系统球面轴承表面正压力的分布情况，并据此提出了相应的改进措施。
Second, the bottom panel of the surface to avoid led drilling hole position is fixed by the screw to install wall on, installed according to the design of plate and fixed thread on each word.
将面板底面避开LED位置钻孔用螺丝固定再安装壁面上，按设计之板安装好，并将每个字的线头固定好。
It is found that there are slip steps of screw dislocations, growth steps and microcrystals on the surface.
发现在金刚石表面存在大量的台阶和微晶。
Screw bat of feed hopper abopted with alloysteel, special handing on surface, durabie in heat, wear and corrosion.
螺杆料筒采用优质合金钢，表面氮化处理，耐热、耐磨、耐腐蚀。
Before spraying, the axes are turned out screw thread and extruded, thus many hooks are arranged on the surface of parts, it strengthens the mechanical combination of spraying layer and substrate;
在喷涂前，对轴类零件粗车螺纹并进行挤压，使基体表面形成钩子形状，增加喷涂层和基体的机械结合力；
The article on the hook is attached to the wall surface, so that the screw has smaller moment and can be used for hanging heavier articles.
钩挂的物体紧贴壁面，螺杆所受力矩较小，可悬挂更重的物品。
The article on the hook is attached to the wall surface, so that the screw has smaller moment and can be used for hanging heavier articles.
钩挂的物体紧贴壁面，螺杆所受力矩较小，可悬挂更重的物品。
应用推荐