Inspection of the pump shaft seal ring, such as wear parts should be replaced.
检查水泵轴的油封环，如磨损严重应更换新件。
Adjusting the seal ring you can get the best seal.
调整密封圈的押紧程度，可以获得最佳密封效果。
The special support frame can perform connection function and connect cooling water to cool down the seal ring.
特殊安装支架，即起到连接作用， 同时又能接通冷却水对密封圈部位进行冷却。
These valves feature an eccentrically mounted disk and a PTFE or 316 stainless steel seal ring.
这些阀门具有一个偏心安装的磁盘和聚四氟乙烯或316不锈钢密封环。
And the deployment of fire extinguishing force for seal ring fire and floating roof explosion fire was emphasized.
重点对密封圈火灾和浮顶爆炸火灾的火灾力量部署进行分析确定。
Basic structure of the centrifugal pump is composed of six parts, namely: impeller, pump, pump shaft, bearing, seal ring, stuffing box.
离心泵的基本构造是由六部分组成的，分别是：叶轮，泵体，泵轴，轴承，密封环，填料函。
The pump comprises mainly of pump body, cover, impeller, shaft, seal ring, intermediate support, sealing and suspension assembly, etc.
泵主要由泵体、泵盖、叶轮、轴、密封环、中间支架、密封和悬架部件等组成。
If the residual air in cylinder is impacted by abrupt clamp pressure the seal ring will be damaged due to the effect of diesel oil.
如果油缸内残留空气受急剧夹压时，那么，由于液压油的作用，有可能使密封圈烧损。
Carbonization is the use of carbon graphite - graphite seal ring when one of the main reasons.
石墨炭化是使用碳—石墨环时密封失效的主要原因之一。
First, the water pump mechanical seal ring on the surface of metal corrosion.
第一，水泵的机械密封上金属环表面均匀腐蚀。
It confirms that tempering quality after being circle checked is the main cause for deformation of the steam seal ring made by rolling.
通过分析，确认校圆后的回火质量是钢板卷制汽封圈产生变形的主要原因。
Former deputy leaves on the cover can reduce the imports of the vortex impeller and particle loss of the wear and tear on the seal ring.
前盖板上的副叶片可以减少叶轮进口的旋涡损失和颗粒对密封环的磨损。
The crimped head design, prevents solids from dislodging the seal face, allows the seal to withstand higher pressure and rotational speed and eliminates the metal shell from contacting the seal ring.
波纹式头部设计，防止固体颗粒从密封面上撞出，使得密封能够抵抗更高的压力和旋转速度，避免金属壳接触到密封环。
Under normal circumstances, after a spring in the long run will be shortened in length, compensation spring moving mechanical seal ring because centrifugal force will cause deformation.
一般情况下弹簧在长时间运行后长度会缩短，补偿弹簧在动环上的机械密封还会因为离心力的原因而变形。
The oven is made of thin steel sheets, fiberglass is inserted between the working chamber and outer plate of the oven as thermal insulation, there is a seal ring embedded in the door.
烘箱由薄钢板构成，工作室与箱体外壳间以玻璃纤维作保温材料、门面镶有密封圈。
If water seal ring, should check with the stuffing at the top of the range is correct.
如有水封环，应检查其与填料函顶部的距离是否正确。
The finite element model of rubber dynamic auxiliary seal ring which was installed on the pusher type mechanical seal was established.
建立了滑移式机械密封装置上动态辅助橡胶密封圈的有限元模型；
It provides a theoretical basis for designing the mechanical seal ring equipment.
这为合理设计机械密封装置提供了理论依据。
Generally use the soft rubber type sealing ring seal, hard seal ring-type metal seal used.
软密封型一般采用橡胶环密封，硬密封型通常采用金属环密封。
Three kinds of injection sleeves construction, materials, surface treatment and application ranges of floating end face seal ring by die casting are expounded.
叙述浮动端面密封环压力铸造的三种压射套结构、材料和表面处理工艺及其应用范围。
Manufactured by casting polyurethane, main seal ring used in expansion ring testing device for pipeline was designed.
采用浇注型聚氨酯材料，设计了一种管道用胀环试样试验台主密封圈。
The tube connector and "O" shape seal ring of the valve must be kept clean, and the cross section line of the tube connector cannot be painted.
联接管与阀口“O”形密封圈套入处应保持清洁， （见图20） 联接管有剖面线的部位处不能涂油漆。
Different body materials and seal ring compound folder layer are suitable for different medium.
更换阀体材质和密封圈复合夹层可适用不同介质。
According to the surface abrasion form of cast iron seal ring, the author proposed that composite brush plating can effectively repair and strengthen the mating surface of cast iron seal ring.
根据铸铁密封环的表面磨损形式，提出采用复合刷镀技术可有效修复和强化铸铁密封环的配合面。
Teflon - lined pipe, casing, elbow, the three exchanges or four, size head, cylinder, air compressor - oxygen - ring, gasket seal ring and auto parts.
聚四氟乙烯内衬直管，套管，弯头，三通，四通，大小头，筒体，空压机-制氧机-活塞环、密封圈和汽配封圈。
The shape of the Simplex stern tube seal ring is so complicated that its characters can not be analysed by ordinary methods.
船舶尾轴的辛泼来克司密封环形状非常复杂，用一般方法难以进行分析。
The front piece includes a foot portion defining an axially extending engagement surface for interference-fit engagement with the annular surface of the seal ring.
前件包括限定与密封环的环形表面干涉配合式接合的轴向延伸的接合表面的足部。
The turning process of carbon-graphite M104 seal ring is focused, and the comparative experimental study on conventional machining and laser-assisted machining are performed.
针对碳石墨M104密封环的车削加工过程，进行了常规切削和激光辅助切削的对比实验研究；
The effects of material composition, working surface treatment and microstructure on wear resistance of powder hot-forging flow oil-seal ring were studied.
研究了粉末热锻浮动油封密封环的材质、表面处理、显微组织对其耐磨性的影响。
The seal assembly comprises a seal ring, a seal ring shell and bellows.
密封组件包括密封环、密封环壳体和波纹管。
应用推荐