The utility model solves the problem that the wheat which is harvested by an original harvester is random, is inserted inversely, and moves the fixed guillotine shear plate.
本实用新型解决了原机被割麦子杂乱、倒插动定剪板的问题。
In the connection design of steel structure, the shear plate with high-strength bolt connection is extensively used at the flexible joint where the beam is connected to the weak axis of the column.
钢结构节点设计中，梁与柱弱轴方向的柔性连接常采用剪力板高强螺栓连接，螺栓群所承受的荷载有竖向力和偏心力矩。
Prefabricated shear wall and composite plate are the key components of the production cost of PC components.
预制剪力墙和叠合板建安费用是影响PC构件生产费的关键因素。
Abstract: shear force is interrelating with width and thickness of plate and obliquity of knife-edge.
文摘：斜刃剪切时，剪切力的大小与板料的宽度、厚度及斜刃倾角有关。
In the range of incident velocities near to the perforation limit velocity (V50), this mechanism depends on thickness and interlaminar shear strength of composite plate.
在接近穿孔极限速度的入射速度(V50)范围内，这一机制依赖于复合材料板的厚度和中间层剪切强度。
The oscillation of the shear layer decreases with the increase of the plate length.
随着腔内平板长度的增加，剪切层振荡的程度有所减小。
This chapter indicates buckling modes, critical load and equilibrium path of plate under axial compression and shear load.
介绍板在单向压缩和剪切载荷作用下的屈曲模态、临界载荷和平衡路径。
Shear force is interrelating with width and thickness of plate and obliquity of knife-edge.
斜刃剪切时，剪切力的大小与板料的宽度、厚度及斜刃倾角有关。
This paper compared several mechanical models with transverse shear deformation and put forward a kind of layer model assuming that shear stresses vary parabolically through the plate thickness.
比较了考虑横向剪切变形的几种力学模型，提出了一种新的假定剪应力沿板厚呈抛物线分布的分层模型。
General analytic solutions for transverse bending of anisotropic rectangular plate using first order shear deformation theory is obtained at the first time by the complex series method (CSM).
采用复级数方法首次建立了基于一阶剪切变形理论的各向异性矩形板横向弯曲一般解析解。
Based on the first order shear deformation theory and Hamiltonian principle, the governing equations and boundary conditions of rotating multi-layer annular plate were derived.
基于一阶剪切变形理论和哈密顿原理，建立了旋转层合圆板动力学运动方程和相应的边界条件。
A kind of finite segment element model for analysis of shear lag effect in plate and truss composite girder is proposed. The model avoids certain deficiencies in conventional calculations.
提出一种板桁结合梁剪滞效应分析的有限段单元模型，避免了常规计算方法中的某些不足。
The structure coordination and shear unlocking middle thick plate element is a problem to which people pay close attention in the finite element analysis of plate.
在板的有限元分析中，构造协调和无剪切闭锁现象的中厚板单元一直是人们所关注的问题和难题。
The bearing capacity of soft subsoils of Xiangtan-Shaoyang Expressway is been studied by the methods of slab loading test, the portable dynamic probe test and the cross plate shear test.
选用平板荷载试验、轻便动力触探试验、十字板剪切试验等三种测试手段，对潭邵公路软土地基承载力进行了研究。
Based on the first-order shear deformation plate theory, axisymmetric governing buckling equations are derived for a functionally graded material circular plate subjected to in-plane pressure.
基于一阶剪切变形板理论，推导了功能梯度材料圆形板在边界面内均布压力作用下的轴对称屈曲方程。
The bending and shear modifying coefficients are derived according to the distribution of the stress and strain of the sandwich plate along the direction of the plate thickness.
根据夹层板的正应力、正应变和剪应力、剪应变沿板厚的分布关系，得到夹层板的弯曲、剪切修正系数。
Yes. We have built up the sound-proofing housing for main noisy equipments such as rotary shear, plate stacker, hydraulic station and so on.
我们针对主要的噪音设备例如回转剪切机、收板机及液压站等建立了隔音室。
While shielding set of processing technology mainly divided into next makings shear, rolled plate forming, welding, straightening round, test and assembly several processes.
而屏蔽套的加工工艺次要分为下料剪切、卷板成形、焊接、矫圆、试验和组装几个工序。
The experimental investigations were performed on the impinging shear flow that is comprised with a jet shear layer impinging a plate parallel to the jet.
本文对撞击剪切流，即射流剪切层撞击顺流放置的平板的流动，进行了实验研究。
The yield conditions of axisymmetric circular plate and shallow spherical shell of reinforced concrete based on Twin shear stress yield criterion are presented in the paper.
导出了基于双剪屈服准则的钢筋混凝土球扁壳的屈服条件，并利用此屈服条件求解出其极限荷载。
The platelet adhesion on surface of fibrillar collagen under high shear rate condition was observed by parallel plate flow chamber with McAb.
利用平行板流动小室技术研究在高剪切力条件下该单抗对血小板在胶原表面黏附的抑制效果。
Design of blade carrier of plate rotary shear has been introduced by analysis of moving mechanism of hydraulic plate shear.
通过分析液压剪板机剪切机理，介绍了剪板机刀架总成的设计。
As a new lateral resisting element, steel plate shear wall with vertical slits has favorable integrative benefits.
带缝钢板剪力墙作为一种新型的抗侧力构件，有着良好的综合效益。
The thickness of the steel plate handled by this roller mill (shear machine) is 25millimeters.
这台滚压机(剪切机)添工的钢板厚度可达25毫米。
Aiming at this special structure, the medium thick plate used in transition storey and its supporting shear walls are analyzed.
针对该结构的特点，着重分析和计算了转换层的中厚板和支承在中厚板上的剪力墙。
A new method for computing shear strength of reinforced concrete flat plate without shear reinforcement while transferring shearing force only is presented herewith.
提出了无剪切钢筋的钢筋混凝土平板在仅传递剪力时，其抗剪强度的计算方法。
Triple junction is the intersection point among three plate boundaries. The boundary could be tensional, compressional or shear fault.
三条板块边界常相交于一点，这一个交点就叫做板块三联接合点（简称三联点，或称三节点）。
It is pointed out that punching shear of plate and shear of oneway plate are two special cases of shear resistance of plates.
本文指出双向平板的冲切问题与单向板的抗剪问题是平板抗剪问题的特殊情况。
The computational results of the simulated test show that the improved steel plate shear wall with slits can produce plastic deformation and consume a great quantity of earthquake energy.
模拟试验过程的计算结果表明，改进的带缝钢板剪力墙可以增加延性，耗散较大的地震能量。
The computational results of the simulated test show that the improved steel plate shear wall with slits can produce plastic deformation and consume a great quantity of earthquake energy.
模拟试验过程的计算结果表明，改进的带缝钢板剪力墙可以增加延性，耗散较大的地震能量。
应用推荐