A signal is a software interrupt.
信号(signal)是软件中断。
Compare with software interrupt.
对比软件中断。
It is important to note that these tasklets/bottom halves will run close to the interrupt context (software interrupt).
有一点值得指出的是，这些tasklet/bottomhalf会关闭这个中断上下文（软件中断）。
Softirqs were originally designed as a vector of 32 softirq entries supporting a variety of software interrupt behaviors.
软中断最初为具有32 个软中断条目的矢量， 用来支持一系列的软件中断特性。
The pointer to a row can contain some value which causes a hardware or software interrupt in case the row is not in memory.
指示器的指示字还包含一个值，当相应行不在存贮器中时，它引起硬设备或软设备中断。
The interface on the destination (the server) receives the incoming SYN packet, places it on the ipintrq queue, and raises a software interrupt.
目的地(服务器)上的接口接收传入syn包，将其放在ipintrq队列中，并引发软件中断。
The control system USES software interrupt control system structure and subroutine is simple, clear in the economic conditions in the application of NC more.
该控制系统采用软件中断控制系统结构及子程序结构简单，条件明确在经济型数控中应用较多。
A piece of software executed in response to a particular interrupt.
响应特定中断而运行的一小段软件。
When the interrupt service routine exits, control of the processor is returned to whatever part of the software was previously running.
当中断服务程序退出，对处理器的控制权转到先前运行的那个软件上。
The interrupt level conflicts with another device in the system. Reconfigure the adapter and software to use a different interrupt level.
中断级别跟系统中的另一个设备有冲突。重新配置适配器和软件来使用不同的中断级别。
It is also possible for an ill-behaved software program to use the timer-counter for another purpose and change the interrupt rate.
它也有可能是病态的软件程序，以用于其他目的，定时器，计数器和中断率的变化。
Flexible setting of interrupt and DMA is adopted in the software design, which improves the efficiency of data transfer and performance of DSP.
在软件设计中，通过灵活设置中断与DMA，不仅提高了图像数据的传输效率，而且充分发挥了DSP的高速性能。
On software, we take full advantage of the low power modes of the MCU to finish the task in ISR (interrupt service routine), so, the power of system rest with the ISR executive time.
在软件设计上，充分利用所选单片机的低功耗模式，让检测任务在中断服务程序中完成，使系统的功耗主要取决于中断服务程序执行的时间。
Data between X9241 and SCM is transmitted with I2C Bus, and the software includes main program and interrupt subprogram.
X9241采用二线串行i2c总线与单片机传递数据。其软件由主程序、中断子程序组成。
A method on expansion of multilevel interrupt priority for MCS 51 single chip computer with software is studied.
介绍了一种在不增加任何硬件的情况下用软件扩展MCS -51单片机多中断优先级的方法。
At last, in the section of software design, startup code programming, operating system choosing and transplanting, task design, drivers design and interrupt service routine design had been discussed.
最后，在软件设计部分探讨了启动代码编写、操作系统的选择和移植、任务规划和设计、驱动程序设计以及中断服务程序设计。
The meaning and the software realization of the interrupt vector table relocation is introduced.
介绍了中断向量表重定位的含义、中断向量表重定位的软件实现过程。
The software is programmed in assembly language, including initialization, key-press and interrupt program such as corresponding subprogram, external and serials.
软件采用汇编语言编写，包括初始化、按键及相应子程序、外部和串口等中断程序。
Interrupt request with the low power mode ensures the low-power of heat meter in the aspect of software.
中断请求配合低功耗模式从软件方面保证了热量表的低功耗。
The software consists of system initialization, display and interrupt service routines, which completes depth and velocity calculations, depth correction and alarm displays.
软件部分由系统初始化与显示程序和中断服务程序组成，主要完成深度、速度的计算、各种校正处理及显示各种报警等功能。
PL/M-96 program language is used as the software of the controller. The signal frequencies are distinguished and the persistence time of the frequency is accumulated with interrupt process routine.
数字化控制器控制软件采用PL/M-96高级语言编程，其中断处理程序用于辩别信号频率、累计每一频率持续时间。
After analysis the function of system software, main program, interrupt service program and subroutine were designed use modeling develop ways.
分析了系统软件的功能，采用模块化软件设计方法，设计了控制系统主程序、中断服务程序以及子程序。
Through the fixed time interrupt design in the software, the real-time put out of the PWM waves was met.
通过软件定时中断设计以满足PWM波形的实时输出要求；
The system software involves five main modules: initialization module, phase-changing module, current-regulating module, speed-regulating module and timer interrupt module.
软件分为五块：主程序中的初始化模块、换相子程序模块、电流调节、速度调节子程序模块，定时器中断程序模块。
Which means a system must be tolerable of faults and can be maintained and upgraded without interrupt service. From the aspect of software, high availability revolves mainly around faults recovery.
这就要求系统能够容错，并能够在不中断服务的情况下维护与升级，从软件设计的角度来看，高可靠性以故障恢复为主要内容。
This paper describes the software main program circle and the major interrupt program.
并介绍了软件主程序和主要的中断程序。
This paper will introduce a useful method of implementation of the aborting function by appending a few hardware and software, and using any spare interrupt source in users application system.
本文介绍一种在用户系统中添加很少量的硬件和软件，利用任一多余的中断源实现夭折功能的方法。
Reconfigure the adapter and software to use a different interrupt level.
配置适配器和软件来使用不同的中断级别。
The system software includes the main program and interrupt service program.
系统软件主要由主程序和中断服务程序组成。
The system software includes the main program and interrupt service program.
系统软件主要由主程序和中断服务程序组成。
应用推荐