Therefore, steam injection parameters for Nine-7 Block were analyzed and optimized using orthogonal experiment design.
为此，利用正交试验设计方法对九7区注汽工艺参数进行了敏感性分析和优化。
The online measurement of the steam quality is a difficult problem of world in petroleum industry, because of high temperature and high pressure of steam and narrow space of steam injection well.
注汽过程中高温高压和狭小的空间，使得干度在线测量成为石油开采行业中的世界性难题。
Method Steam injection development and well pattern of horizontal Wells were studied by using numerical simulation.
方法利用数值模拟方法，对水平井注蒸汽的开发、布井方式等进行研究。
The improvement in power output and fuel consumption brought about by steam injection is quite impressive by any standard.
回注蒸汽后在功率、耗油率方面的得益令人印象深刻。
In the actual application, sequential response value of steam quality is measured under steam injection well with high temperature and high pressure.
在初步的实际应用中，得到了注汽油井井下高温高压蒸汽干度变化的连续响应值。
Conclusion This method is suitable to whole process of heavy oil development by steam injection, and it is an effective method.
结论该方法适用于稠油油藏注蒸汽开发的全过程，是一种有效的方法。
Pressure transient test in steam injection well is an inexpensive and effective means to determine swept volume and flowing condition of the steam zone.
注蒸汽井压力降落试并是确定蒸汽波及体积和了解波及区流动情况的一种经济、有效的方法。
Under the production condition of steam injection, the energy ratio can reach 7.0.
在注入蒸汽开采初始条件下，能量效率可以达到7.0。
Vibration blocking removal technologies, acid fracturing technique, steam injection, water injection were generalized successfully in oil recovery process.
在采油生产中已成功推广了振动解堵、酸化压裂解堵、注蒸汽、注水等增产技术。
This article reviews the chief techniques of EOR by steam injection with ancillary additives.
本文综述了国外添加化学剂注蒸汽采油的主要技术。
On the basis of casing bearer analysis and field experience, this paper gives casing elongation calculation formula of cold production Wells in the process of steam injection.
在重点分析套管综合受力的基础上，结合现场经验，推导出了常规井注汽井口套升计算公式。
Heat efficiency of steam injection and hot water injection was 0.349 and 0.465 under the given condition.
在给定的条件下，注入蒸气和热水开采过程的热量的有效利用率分别为0.349和0.465。
Study on the operation thermal efficiency of steam injection boiler steam injection boiler is the key equipment of the system.
提高注汽锅炉运行热效率研究注汽锅炉是注汽系统的关键设备。
A most effective method of heavy oil production throughout the world now is thermal production through steam injection.
注蒸汽热力采油是当今世界开采稠油最有效的方法。
Through numerical modelling, this paper studies the process parameters of steam drive such as steam injection rate, production injection ratio, and steam quality.
利用数值模拟方法对蒸汽驱中注汽速度、采注比和蒸汽干度等工艺参数进行了研究。
The first period of production shows that the result of steam injection is good.
从第一周期开采过程看，注汽效果较好。
Major factors which influence the steam injection profile are steam overlaying and high-permeability zones during steam flooding and cyclic steam injection.
在蒸汽驱和蒸汽吞吐过程中，影响蒸汽注入剖面的主要因素是蒸汽超复现象和高渗透层。
Because it can not predict the future index, this paper combine the injection-production-curve method with HCZ model, find the method of predicting steam injection and heavy oil production.
鉴于其不能对未来进行预测，提出了应用注采曲线法同hcz模型相结合对现场注入蒸汽及稠油产量进行预测的方法。
The sensitivity analysis indicates that the parameters impacting the production results from high to low are production time, steam dryness, cyclic steam injection volume, steam injection pressure.
敏感性分析表明，蒸汽参数对开发效果影响的顺序从大到小依次为生产时间、注汽干度、周期注汽量、注汽压力、焖井时间和注汽速度；
Based on calculation results of heat balance of steam injection boiler, this paper finds causes of operational heat efficiency low.
根据油田注汽锅炉热平衡测算数据及结果分析，找出了其运行热效率低的原因。
The temperature behavior within the Poplar flake-board mat during steam injection vacuum pressing (SIVP) was studied.
研究了喷蒸真空热压杨木大片刨花板坯内部的温度分布特征。
With a pilot steam injection device a better fuel adaptability can be achieved. As compared with chain grate stoker, it has the advantages of simple structure and less metal consumption.
配用蒸汽引射装置后，可达到一种炉型适应多煤种的目的：与链条炉排比较，具有结构简单，金属耗量少等优点。
Purpose To determine oil recovery factor and recoverable reserves of heavy oil reservoir developed by steam injection.
目的确定稠油油藏注蒸汽开发的原油采收率和可采储量。
A forced-closing-and-opening plunger pump is developed to solve the problems of gas lock and sand inflow and low pump efficiency in steam injection Wells.
针对辽河油田蒸汽吞吐油井存在气锁、出砂、后期油稠泵效降低的状况，研制了强启闭柱塞抽油泵。
This paper analyzes current technical conditions of the control system of steam injection boiler and proposes a comprehensive plan.
分析了注汽锅炉控制系统技术现状，提出了注汽锅炉控制系统综合技术方案。
The statistics of 36 oilfield steam drive pilot test results show that the oil-steam ratio depends on not only the reservoir parameters, but also the steam injection rate.
国外36个蒸汽驱现场试验结果统计规律表明，蒸汽驱油汽比不仅与地质参数有关，而且与注汽速度密切相关。
The statistics of 36 oilfield steam drive pilot test results show that the oil-steam ratio depends on not only the reservoir parameters, but also the steam injection rate.
国外36个蒸汽驱现场试验结果统计规律表明，蒸汽驱油汽比不仅与地质参数有关，而且与注汽速度密切相关。
应用推荐