But such force is ignored in structure design and strength calculation.
但在筒体结构强度设计计算中此项冲击力是忽略不计的。
And it is a long standing problem to simplify their strength calculation.
如何对其进行简化计算是一个由来已久的问题。
Of course, skipping this strength calculation saves some decoding time as well.
当然，跳过这个强度计算可以节省一些解码时间。
Main resonance amplitude of a shaft is concerned with the strength calculation.
传动轴的主共振的振幅与传动轴的强度计算有关。
The load coefficient method of bolt on tensile strength calculation was improved.
对螺栓拉伸强度计算的载荷系数法作了进一步改进。
Based on completion of wall strength calculation, then do the finite element stress analysis.
在完成管壁强度计算的基础上，进行管壁有限元应力分析。
This paper describes and analyzes the design and strength calculation of planetary transmission.
本文对行星传动的设计和强度计算等内容作了详细的分析论述。
The methods of estimating configuration factors and strength calculation are presented in the paper.
文章介绍了形状系数的估算方法和强度计算方法。
Since the value of inertial forces of goods during transportation is the basis of fastening strength calculation.
货物在铁路运输过程中各种惯性力力值，是加固强度计算的基本依据。
In the range of research, the tubing failure is not strength calculation problem under internal pressure and axial load.
在所研究的范围内，得出了内压和轴力作用下，油管失效不是油管强度不足的结论。
Moreover, the paper presents a relatively simple and comprehensive theoretical method for torsional strength calculation.
同时，提出了这类双壳大舱口船舶扭转强度的理论计算方法。
The tubular backbone is the main loading member of motorcycle frame, which needs reliable strength calculation when designing.
摩托车车架主管是摩托车的主要承载构件，设计时要进行可靠的强度计算。
So the effects of these factors on mechanical properties of materials are needed to be considered in the strength calculation.
因此在强度计算时常需考虑这些因素对材料力学性能的影响。
It describes that tower construction technique, process, strength calculation and apparatus selection by using the internal gin pole.
并介绍内抱杆组立铁塔施工技术、施工工艺、受力计算和工器具选择。
Just because of this, it's very hard for us to evaluate the ship structural strength, which based on whole strength calculation method.
由于这一系列的特殊性，采取规范的总强度计算方法难以合理地评估船体强度，且采用舱段模型进行直接计算也存在困难。
The strength calculation formula of the screw propeller under the action of centrifugal force was obtained through multivariate fitting.
经多变量拟合，得到了离心力作用下螺旋推进器的强度计算公式。
If the strength calculation of piping components is to be made, the allowable stresses of the piping materials shall be determined fist.
要对管道元件进行强度计算，首先就要确定管道材料的许用应力。
In the past, this character was not considered in the strength calculation of gun barrels and the effect of the axial stress is ignored.
已往在进行火炮身管强度计算时，均不考虑材料的这一性质，而且也都忽略了轴向应力的影响。
PLUSTRUSS Provided strength calculation for different truss type, which would be the "safety guilder" When customer is using our trusses.
PLUSTRUSS提供不同桁架的强度计算类型，它将“安全金币”，当客户使用我们的桁架。
The author introduces the strength calculation of lifting up and moving the whole iron tower and Us application m engineering construction.
本文介绍将线路铁塔整体提升平移的受力计算及其在实际施工中的应用。
Through the project example, the strength calculation method for local wall pier under the cantilever beam of a brick-residence was discussed.
通过工程实例，对砖混住宅挑梁下的局部墙垛的强度计算方法进行了探讨。
The differences between chinese and Japanese boiler standards from the aspects of design, strength calculation and hydrostatic test are compared.
从设计、强度计算及水压试验等方面比较了中日锅炉标准的差异。
Perform mechanical design and strength calculation check; review and check vendor design drawing, strength calculation and bill of materials, etc.
负责机械设计和强度计算核查；审阅和检查供应商设计图纸，计算书和材料清单等。
In the strength calculation of the premise, the first use of the European crane design manual on structural stability of the calculation of check.
在强度计算的前提下，首先运用欧洲起重机设计规范对结构稳定性进行手工计算校核。
The forces on the lifting lug in the upper and tail of the vertical vessel were analyzed, and the strength calculation and formula were presented.
分析了直立设备的顶部吊耳及尾部吊耳的受力，提出了其强度核算的方法及公式。
Introduces the main ideas of the software system that is developed from China GB9222-88(Strength calculation of pressure parts for water tube boiler).
介绍了根据GB92 2 2 88《水管锅炉受压元件强度计算》而开发的实用软件系统的设计思想。
The paper discussed the strength calculation of the growing circle bure of small scale vertical boiler, and put forward his opinion according its stress.
就小型立式锅炉长圆孔开孔强度计算进行了探讨，根据长圆孔的应力状态，提出了自己的看法。
Ratings are based on strength calculation. Basic static strength rating, or for hand operation of above gears, is approximately 3 times the 100 RPM rating.
评级建立在强度计算上。基本的静态强度等级、或用手操作的设备以上齿轮的3倍，大约是100每分钟转速的评价。
But the mechanical properties of weld joint have influence on selection of welding technology and welding material, and on strength calculation of construction.
而接头性能直接影响着结构焊接工艺的选择和强度计算。
The key techniques such as model simplification, node division, section feature calculation, strength calculation method and result output format are introduced.
介绍了系统开发的关键技术：模型简化、节点划分、平面图形截面特性的计算、强度计算的算法及分析结果的输出形式。
应用推荐