Next mold will be made from high tear strength RTV for sure.
模具明年将作出从高撕裂强度室温硫化肯定的。
For instance, 300%modulus was increased by 77% and tear strength by 38%.
例如，300%定伸应力提高了77%，抗撕裂强度提高了38%。
Consider the bursting strength that is required and the tear strength desired.
考虑爆破强度是必需的，所需的撕裂强度。
The introduction of OR into SBR and NR enhanced their hardness and tear strength .
纳米累托石的加入可以显著提高SBR和NR的硬度和撕裂强度。
Silicone tubing has some limitations, including lower tear strength when compared with PU tubing.
硅胶管有一些限制，包括降低撕裂强度相比，PU管。
In this paper, research on curing system of vulcanized silicone rubber aging tear strength after impact.
本文主要研究论述硫化体系对硫化硅橡胶老化后撕裂强度的影响。
It has a very high tear strength, high abrasion resistance and is extremely resistant to oils and greases.
它有着高撕扯性，高耐磨性，及非常好的抗油性。
The cause leading to deviation of tear strength in measuring tear strength of silicone rubber vulcanizate was analyzed.
分析了在热硫化硅橡胶混炼胶撕裂强度的测试中撕裂强度出现偏差的原因；
Tear strength: it is the force required to tear a paper at a precut edge to a specific length and measured in milli-newton.
撕裂度：把一张事先切一小口的纸，撕开到一定长度所需的力，以毫牛顿计算。
It is mainly used as rubber reinforcement and filler, to improve their elongation, tear strength and resistance to abrasion.
主要用作橡胶制品的补强剂和填充剂，能明显改善橡胶制品的抗拉强度、抗撕裂性和耐磨性。
LDPE (Low Density Polyethylene) : Offers such advantage as tear strength and high chemical resistance. It is also waterproof.
(低密度聚乙烯)：具有以下优良性质：高撕裂强度，高耐化学性，防水性。
It has a better flex cracking resistance than those of natural rubber but a lower tear strength and a higher dynamic modulus.
它比天然橡胶具有较好的抗挠曲开裂性能，但撕裂强度较低，动态模量较高。
LDPE (Low Density Polyethylene) : Offers such advantage as tear strength and high chemical resistance. It is also waterproof.
LDPE(低密度聚乙烯)：具有以下优良性质：高撕裂强度，高耐化学性，防水性。
The results showed that the tensile strength, elongation at break and tear strength increased with the OMMT content increasing.
测试结果表明，随着蒙脱土用量的增加，复合材料的定伸应力、拉伸强度和撕裂强度均大幅度提高。
The results showed that the filling of short fiber evidently improved tear strength, modulus at 10%and Shore A hardness of SFRC.
结果表明，短纤维的加入显著提高了SFRC的撕裂强度、10%定伸应力及邵尔A型硬度；
The tensile strength, elongation at break and tear strength of TAIC were higher than those of PDM while the compression set was opposited.
随着硫化助剂用量增加，TAIC共混胶的拉伸强度、拉断伸长率和撕裂强度均大于PDM共混胶，而压缩永久变形的变化率正好相反。
There lie some correlations among mechanical properties. In this paper, we will take tear strength for example to discuss this correlation.
物理性能参数间存在着相互关系，该文将以撕裂强度为例对其进行探讨。
The results showed that when compared with SBR, the NBR filled with calmos CC had higher tensile strength and tear strength, but lower curing speed.
结果表明，随着白燕华CC用量的增大，胶料表现出比填充非极性SBR更高的拉伸强度和撕裂强度，而硫化速度却明显减慢。
The mechanical experimental results showed that PVA had a little effect on the tensile strength, right Angle tear strength and elongation at break, and...
力学性能测试结果表明，加有pva的PE防雾膜在拉伸强度，直角撕裂强度，断裂伸长率等方面比未加PVA的防雾膜要小，但不影响其使用性能。
Methods: the water sorption, the water solubility and the tear strength of two kinds of silicon rubbers were examined and evaluated under the same conditions.
方法：在相同条件下对两种硅橡胶材料进行吸水率、溶解率及撕裂强度测定，对其进行t检验分析。
The silicon and fluorine rubber with high temperature resistance, low compression permanent deformation, and high tear strength properties can meet the water sealing gasket requirements.
采用耐高温、低压缩永久变形、高抗撕裂硅、氟橡胶可以满足该部位需耐高温、耐冷却水的要求。
The results show that the presence of carbon fiber obviously enhances the hardness, heat resistance and oil resistance of the composite, but decreases the tear strength of the composite.
结果表明：炭纤维的加入能提高橡胶的硬度、耐热性及耐油性，但橡胶的扯断强度有所下降。
Hydrolysis: Water and high temperature can change the consistency of certain polyurethanes. Colours change and material crumbles into small pieces. Tensile and tear strength deteriorate.
水解：水和很高的温度可以改变一定的聚氨酯类韧性。颜色改变和原料分成小块，张力和撕力会破坏。
It was shown that MLPB could improve the interface combination between the organic fillers and the rubber matrix, and could increase the tear strength and the stickiness of the IIR rubbers.
研究表明，MLPB能在一定程度上提高有机填料与橡胶基体之间的界面结合强度；同时，也能有效地提高IIR胶料的自粘性能和撕裂强度等性能指标。
The influence of the level of the pretreated short fibre on tensile strength, tear strength, flex fatigue and conductivity of the acetylene black filled VMQ/EPDM blend vulcanizate was studied.
研究了预处理短纤维用量对乙炔炭黑填充甲基乙烯基硅橡胶（VMQ）／EPDM共混硫化胶拉伸、撕裂、耐屈挠疲劳和导电性能的影响。
The experimental results show that when the matching between Aramid fiber and PPTA is 1:1.5 more or less, the tensile strength, tear and formation of aramid paper is the best.
实验结果表明，当芳纶短切纤维与芳纶浆粕的配比为1：1.5左右时，所抄造纸页的抗张强度、撕裂度、匀度最好；
The tensile strength and tear of aramid paper that papermarking for two is strong than the aramid paper which is papermarking for one.
分层抄造的芳纶原纸比一次抄造的芳纶原纸的抗张强度和撕裂度高；
Tatar tear out four, according to Hulunbeier grassland, increase in strength.
灭塔塔儿撕四部，据呼伦贝尔草原，实力大增。
Bulk density of small materials, heat conduction tear your eyes coefficient is generally small, but at the same time decreases in the mechanical strength, so be reasonable choice.
容重小的材料，一般导热泪盈眶系数也小，但同时机械强度也随之降低，故要合理选择。
Bulk density of small materials, heat conduction tear your eyes coefficient is generally small, but at the same time decreases in the mechanical strength, so be reasonable choice.
容重小的材料，一般导热泪盈眶系数也小，但同时机械强度也随之降低，故要合理选择。
应用推荐